Husqvarna 1130SB owner manual Axle Shaft, Roll PIN 3/16, Gear, Clik PIN

Page 34

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

	7
1b	4
8	3
	3
1b
7	1a
	1a

	2
5	3
5
	4
6	01.03.001-A

KEY	PART		DESCRIPTION
NO.	NO.		DESCRIPTION
1	532	40 49-23 (assy of 1a,1b) AXLE ASSEMBLY
1a	532	40 43-07	AXLE SHAFT
1b	532	18 42-06	ROLL PIN 3/16
2	532	18 00-81	GEAR

3532 17 46-97 THRUST WASHER

4532 17 98-30 AXLE BEARING

5532 14 63-15 SCREW 5/16−18 X .625

6817 49 05-08 BOLT 5/16−18 X .500

7	532 15 54-43	CLIK PIN
8	532 18 92-82	SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 34

Contents 1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts KEY Part Description Auger 30 LH CARRIAGEBOLT5/16−18X.625Auger 30 RH Plastic Retainer Repair Parts Auger Housing / Impeller AssemblySkid Plate Weight BAR CARRIAGEBOLT5/16−18X.750Deflector Weldment Deflector Control AssemblyChute Weldment Knob BlackLEVER/CABLE Rotator Assembly Gray 532 42 11-61 Rotator Pivot Bracket532 42 Lower TubeHandles Rear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb 532 18 00-82 Intermediate Gear Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly Flange Bearing14 15 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 11 532 18 40-76 Shifter Support BracketGear Axle ShaftRoll PIN 3/16 Clik PINFrame Repair Partschassis / Engine / PulleysEngine TEC Model Bottom PANSteer Cable Bracket LH Steer Cable Bracket RHAxle Lobe Wheel LobeLever PIN Retainer PIN Power Cord532 03 50-62 Safety Ignition KEY Wrench532 18 10-35 DECAL, DANGER, Deflector Decals10 532 18 37-30 DECAL, Remote Deflector Warranty Statement

REPAIR PARTS

DRIVE

KEY

AXLE SHAFT

ROLL PIN 3/16

GEAR

CLIK PIN