Husqvarna 1130SB Repair Partschassis / Engine / Pulleys, Engine TEC Model, Frame, Bottom PAN

Page 35

REPAIR PARTSCHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

1

3

 

3

4

 

 

KEY

PART

DESCRIPTION

 

 

NO.

NO.

 

 

-

- - - - - -

ENGINE TEC MODEL

4

 

 

 

OH318SA-221807B

 

 

1

532 41 61-55

FRAME

 

 

2

532 41 08-77

BOTTOM PAN

2

01.00.018-A

3

532 15 04-06

BOLT 3/8−16

4

532 18 44-71 SCREW 10−24 X .625

 

1

2

3

01.04.008

4

KEY

PART

DESCRIPTION

NO.

NO.

1

532 40 91-61

COVER ASSEMBLY

2

532 17 88-13

PULLEY

3532 41 97-44 TRACTION BELT

4532 40 80-08 IMPELLER BELT

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents 1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts KEY Part Description Auger 30 RH CARRIAGEBOLT5/16−18X.625Auger 30 LH Skid Plate Repair Parts Auger Housing / Impeller AssemblyPlastic Retainer CARRIAGEBOLT5/16−18X.750 Weight BARKnob Black Deflector Control AssemblyChute Weldment Deflector Weldment532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly GrayLower Tube 532 42Handles 13 532 41 54-33 Shifter Plate Bracket Clutch RODRear Plate Bulb 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight Flange Bearing Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly 532 18 00-82 Intermediate Gear14 15 11 532 18 40-76 Shifter Support Bracket 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate WeldmentClik PIN Axle ShaftRoll PIN 3/16 GearBottom PAN Repair Partschassis / Engine / PulleysEngine TEC Model FrameSteer Cable Bracket RH Steer Cable Bracket LHLever PIN Wheel LobeAxle Lobe Wrench Power Cord532 03 50-62 Safety Ignition KEY Retainer PIN10 532 18 37-30 DECAL, Remote Deflector Decals532 18 10-35 DECAL, DANGER, Deflector Warranty Statement
Top Page Image Contents