Husqvarna 1130SB owner manual Handles

Page 28

REPAIR PARTS				HANDLES
SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43
	10
				2
11			7
	8	4	7
	9
	9
	5
6	7
6
			1
3
8			13
8
	13			12
	13
				14
			14	01.08.002-E
				01.08.002-E
		12
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 41 55-39 CONTROL PANEL

2532 41 55-41 CONTROL LEVER LH

3532 41 55-42 CONTROL LEVER RH

4532 41 55-46 TRACTION ROD ARM

5532 42 14-92 IMPELLER ROD ARM

6532 41 26-77 INTERLOCK ROD

7	532 42 16-13	SPACER
8	532 16 96-75	RETAINER
9	817 06 04-08 SCREW 1/4−20 X .50
10	532 41 42-80	KNOB BLACK
11	532 41 42-81	KNOB RED
12	532 17 88-99	HANDLE KNOB
13	819 13 13-16	WASHER 3/8
14	872 12 06-18 CARRIAGE BOLT 3/8−16 X 2.25

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 28

Image 28

Contents 1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts KEY Part Description Auger 30 LH CARRIAGEBOLT5/16−18X.625Auger 30 RH Plastic Retainer Repair Parts Auger Housing / Impeller AssemblySkid Plate Weight BAR CARRIAGEBOLT5/16−18X.750Deflector Control Assembly Chute WeldmentDeflector Weldment Knob BlackLEVER/CABLE Rotator Assembly Gray 532 42 11-61 Rotator Pivot Bracket532 42 Lower TubeHandles Rear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb Rubber Wheel Ring 532 40 61-09 Control Shaft Assembly Assembly532 18 00-82 Intermediate Gear Flange Bearing14 15 532 19 84-74 Speed Selector Head Assembly Trunnion Bearing Assembly532 19 77-63 Drive Plate Weldment 11 532 18 40-76 Shifter Support BracketAxle Shaft Roll PIN 3/16Gear Clik PINRepair Partschassis / Engine / Pulleys Engine TEC ModelFrame Bottom PANSteer Cable Bracket LH Steer Cable Bracket RHAxle Lobe Wheel LobeLever PIN Power Cord 532 03 50-62 Safety Ignition KEYRetainer PIN Wrench532 18 10-35 DECAL, DANGER, Deflector Decals10 532 18 37-30 DECAL, Remote Deflector Warranty Statement

HANDLES

KEY

KNOB BLACK

WASHER 3/8