Husqvarna 1130SB 532 42 14-48 Headlight Bezel Gray, 532 17 86-66 Halogen Headlight, Bulb

Page 30

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

		KEY	PART
	3	NO.	NO.	DESCRIPTION
	2	1	532 41 62-88 INTERLOCK SPRING
5	2	2	532 41 45-72 INTERLOCK CAM
		3	532 17 88-31 TORSION SPRING
		4	532 16 96-75	RETAINER
	1	5	817 06 04-10 SCREW 1/4−20 X .625
	1	6	532 42 18-14 INTERLOCK STOP
		6	532 42 18-14 INTERLOCK STOP
6	01.08.007-B

			4
3			5	KEY	PART
7				KEY	PART	DESCRIPTION
7	2			NO.	NO.	DESCRIPTION
	2
				1	532 42 13-82 PANEL CONSOLE GRAY
				2	532 42 14-48 HEADLIGHT BEZEL GRAY
				3	532 17 86-66 HALOGEN HEADLIGHT
	4	1		4	532 18 44-71 SHOULDER SCREW
5	4			5	532 17 52-62 SCREW 10−24 X 1.25
5				5	532 17 52-62 SCREW 10−24 X 1.25
6				6	532 18 09-64 WIRE HARNESS
6				7	532 40 16-20	BULB
				7	532 40 16-20	BULB
	01.10.013-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 30

Contents 1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger 30 LHAuger 30 RH Repair Parts Auger Housing / Impeller Assembly Plastic RetainerSkid Plate Weight BAR CARRIAGEBOLT5/16−18X.750Deflector Weldment Deflector Control AssemblyChute Weldment Knob BlackLEVER/CABLE Rotator Assembly Gray 532 42 11-61 Rotator Pivot Bracket532 42 Lower TubeHandles Clutch ROD Rear Plate13 532 41 54-33 Shifter Plate Bracket 532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightBulb 532 18 00-82 Intermediate Gear Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly Flange Bearing14 15 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 11 532 18 40-76 Shifter Support BracketGear Axle ShaftRoll PIN 3/16 Clik PINFrame Repair Partschassis / Engine / PulleysEngine TEC Model Bottom PANSteer Cable Bracket LH Steer Cable Bracket RHWheel Lobe Axle LobeLever PIN Retainer PIN Power Cord532 03 50-62 Safety Ignition KEY WrenchDecals 532 18 10-35 DECAL, DANGER, Deflector10 532 18 37-30 DECAL, Remote Deflector Warranty Statement

REPAIR PARTS

HANDLES

KEY

KEY

532 42 14-48 HEADLIGHT BEZEL GRAY

532 17 86-66 HALOGEN HEADLIGHT

BULB