Husqvarna 1130SB LEVER/CABLE Rotator Assembly Gray, 532 42 11-61 Rotator Pivot Bracket

Page 26

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 42 03-37	LEVER/CABLE ROTATOR ASSEMBLY GRAY	*4	01.09.007-A	*5
2	817 50 10-10 SCREW 10−24 X .625				*5
2	817 50 10-10 SCREW 10−24 X .625
*3	532 42 06-78 ROTATOR HEAD
*4	532 42 11-61 ROTATOR PIVOT BRACKET
*5	532 42 06-75	PULLEY PIVOT
*6	532 42 11-62 CABLE ASSEMBLY GRAY

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

1 01.15.004-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 19 24-49 STEER CABLE BLUE

2874 04 10-24 SCREW 10−24 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 26

Contents 1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts KEY Part Description Auger 30 RH CARRIAGEBOLT5/16−18X.625Auger 30 LH Skid Plate Repair Parts Auger Housing / Impeller AssemblyPlastic Retainer Weight BAR CARRIAGEBOLT5/16−18X.750Deflector Weldment Deflector Control AssemblyChute Weldment Knob BlackLEVER/CABLE Rotator Assembly Gray 532 42 11-61 Rotator Pivot Bracket532 42 Lower TubeHandles 13 532 41 54-33 Shifter Plate Bracket Clutch RODRear Plate Bulb 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight 532 18 00-82 Intermediate Gear Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly Flange Bearing14 15 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 11 532 18 40-76 Shifter Support BracketGear Axle ShaftRoll PIN 3/16 Clik PINFrame Repair Partschassis / Engine / PulleysEngine TEC Model Bottom PANSteer Cable Bracket LH Steer Cable Bracket RHLever PIN Wheel LobeAxle Lobe Retainer PIN Power Cord532 03 50-62 Safety Ignition KEY Wrench10 532 18 37-30 DECAL, Remote Deflector Decals532 18 10-35 DECAL, DANGER, Deflector Warranty Statement

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

KEY

LEVER/CABLE ROTATOR ASSEMBLY GRAY

532 42 11-61 ROTATOR PIVOT BRACKET

KEY