Intel 10/100 manual Console Command-line Summary, Console Commands, System Commands

Page 35

C H A P T E R 3

Intel Express 10/100 Fast Ethernet Switch

Console Command-line Summary

Console Commands

help-kbd

Lists the help and shortcut keys.

banner

Displays the Console Manager logo.

clear

Clears the screen.

login

Exits Console Manager and displays the login screen.

logout

Exits Console Manager and any active Telnet session.

set-prompt <new_prompt> Changes the console prompt.

set-passwd

Changes the console password.

System Commands

sys-stat

Displays system status.

get-stst-level

Displays the selftest level.

set-stst-level {noneshortlong} Changes the selftest level.

warm-reset

Performs a warm reset of the switch.

cold-reset

Performs a cold reset of the switch, which is the same as powering it off then on again.

get-last-err

Displays information about the last fatal error.

init-nvram

Resets nonvolatile RAM (NVRAM) to default values.

set-line-slip {96001920038400}

Transfers the serial connection to SLIP mode and sets the baud.

get-sw-file

Displays the SNMP agent software filename.

32

Image 35

Contents User Guide First edition Contents Chapter Troubleshooting Next steps Optional Connect the network devices to the switchCheck the LEDs for power and links Press Eand log into the Console Manager Baud Data bits No parity Stop bit Xon/Xoff flow controlOverview TopologyIntel Express 10/100 Fast Ethernet Switch Installation and SetupRcv Using the SwitchPort status LEDs XmtLink Management status LEDsFiber optic requirements Cabling RequirementsUTP requirements NIC RJ-45 MDI Straight-through vs. crossover cablesDetermining which cable to use Configuring the mixed 10 Mbps workgroup environment Typical ConfigurationsConfiguration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches One repeater hop for Repeater count limitationsGeneral rule for Configuring Accessing the Console Manager remotely Accessing the Console ManagerMeans you can type one of the following Using the Console ManagerEntering commands Vlan Console Manager command groups Sample Console Manager Session Procedures using this diagramSet the IP configuration. Type the command Configuring the Snmp agent for IPCommands used To configure the Snmp agentRecommended environments Configuring a port for full duplexTo configure a port for full duplex To create an Svlan Creating Virtual LANs VLANsTo create a VBD Create the two SVLANs. Type the commandsMonitoring traffic To check traffic on a port Detecting speed mismatches Detecting faulty adapters or hub portsDetecting bad or poor quality cable Detecting congested segmentsStatistic Definitions Configuring and Managing the Switch Reference Group to display commands relevant to that groupSystem Commands Console Command-line SummaryConsole Commands IP Commands Snmp Commands Virtual LAN Vlan Commands Switching Database CommandsSpanning Tree Commands Switching Statistics Commands Port Configuration CommandsLogout Console CommandsHelp-kbd BannerSys-stat System CommandsSet-passwd Set-stst-level Warm-resetCold-reset Get-stst-levelSet-sw-file Init-nvramSet-line-slip Get-sw-fileSw-dnld Set-rsw-fileGet-tftp-srvr Set-tftp-srvrIP configuration IP CommandsSet-ip-conf Get-bootpSet-bootp Set-ipGet-gatew Get-slip-confSet-slip Set-slip-confStops the active ping process. You can also press cC Ping CommandsPing Ping-stopDel-arp-entry Address Resolution Protocol ARP CommandsGet-arp-tbl Add-arp-entrySet-comm Snmp CommandsSnmp community strings Get-commGet-traps Snmp trap message commandsGet-auth Set-authRemoves a station from the trap table Switching Database CommandsAdd-trap Del-trapGet-lt-entry Database control commandsFF-FF-FF-FF-FF-FF Get-lt-16Add-lt-entry Find-lt-addrDel-lt-entry Del-lt-addrSet-lt-age Custom filteringGet-lt-age Add-cf-entry Get-lt-filterDisplays the custom filter table stored in Nvram Vlan CommandsDel-cf-entry Get-nv-cftblGet-vbc-matrix Get-con-matrixSet-sec-vlan Set-vbc-domainDel-vbc-domain Get-vbc-tblMonitor Get-svlan-tblDisplays the table of defined SVLANs Set-mon-portExample Spanning Tree CommandsGet-st-bcfg Get-stpSet-stp Displays the spanning tree state for all ports Get-st-pcfgGet-st-syscfg Set-br-hellot Set-br-prioSet-br-maxage Set-prt-pcost Set-br-fwdelSet-prt-prio Set-prt-enbGet-port-cfg Port Configuration CommandsUse these commands to configure and display port settings Displays the current port configurationSet-port-fctrl Statistics CommandsSet-port-dplex Set-speed-selGet-colls-cnt Get-eth-cntGet-br-cnt Get-rmon-cntGet-sdist-cnt Displays the Rmon statistics packet size histogram for port2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Troubleshooting Flow Control ProblemsIntel Express 10/100 Fast Ethernet Switch System Default ConfigurationSpanning tree Not installed see Accessories on nextPorts Console ManagerStatus Indicators per port SpecificationsFeatures AccessoriesMaximum Cabling Distances General IndicatorsBoot and Configuration Connector InterfacesAC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2A Electrical SpecificationsPower Cord Specifications Electromagnetic Emissions and Safety Agency ApprovalSnmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Displaying current state, 44 enabling or disabling IndexControl commands Get-authcommandGet-bootpcommand Database, switchingGet-trapscommand Get-port-cfgcommand, 22Get-slipcommand Get-stpcommandMIB Set-commcommandXmt Transmit LED Set-slipcommandSet-stpcommand World Wide Web & Internet FTP Intel BBS Troubleshooting Software updates Installation notesHow to access