Intel 10/100 manual Switching Database Commands, Add-trap, Del-trap

Page 53

C H A P T E R 3

Intel Express 10/100 Fast Ethernet Switch

add-trap

add-trap <IPaddress> <trap-community>

Enters the IP address of the receiving station and the trap community string that appears in the trap message. The trap table can contain up to five receiving stations.

SYS_console> add-trap 129.1.1.76 engineering

Entry 129.1.1.76 - rnd added

SNMP TRAP TABLE

===============

IPADDRCOMMUNITY

-----------------------------------------------

129.001.001.065 ----------- public

129.001.001.007 ----------- trapcomm

129.001.001.076 ----------- engineering

-----------------------------------------------

del-trap

del-trap <IPaddress>

Removes a station from the trap table.

SYS_console> del-trap 129.1.1.7

Entry 129.1.1.7 - trap comm deleted

Switching Database

Commands

Use the commands listed in this section to manage the switching database.

The switching database is also called a learn table or address table. Each active entry contains the information relevant to a network node, identified by its Ethernet MAC address. Each entry contains the following information:

Lock. If locked (denoted as a +), the entry is static and isn’t deleted by the switch aging process. If unlocked (denoted as a -), the entry is dynamic and is automatically deleted if the workstation is not active during the aging time period.

50

Image 53

Contents User Guide First edition Contents Chapter Troubleshooting Next steps Optional Connect the network devices to the switchCheck the LEDs for power and links Press Eand log into the Console Manager Baud Data bits No parity Stop bit Xon/Xoff flow controlOverview TopologyIntel Express 10/100 Fast Ethernet Switch Installation and SetupPort status LEDs Using the SwitchXmt RcvLink Management status LEDsFiber optic requirements Cabling RequirementsUTP requirements NIC RJ-45 MDI Straight-through vs. crossover cablesDetermining which cable to use Configuring the mixed 10 Mbps workgroup environment Typical ConfigurationsConfiguration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches One repeater hop for Repeater count limitationsGeneral rule for Configuring Accessing the Console Manager remotely Accessing the Console ManagerMeans you can type one of the following Using the Console ManagerEntering commands Vlan Console Manager command groups Sample Console Manager Session Procedures using this diagramCommands used Configuring the Snmp agent for IPTo configure the Snmp agent Set the IP configuration. Type the commandRecommended environments Configuring a port for full duplexTo configure a port for full duplex To create an Svlan Creating Virtual LANs VLANsTo create a VBD Create the two SVLANs. Type the commandsMonitoring traffic To check traffic on a port Detecting bad or poor quality cable Detecting faulty adapters or hub portsDetecting congested segments Detecting speed mismatchesStatistic Definitions Configuring and Managing the Switch Reference Group to display commands relevant to that groupSystem Commands Console Command-line SummaryConsole Commands IP Commands Snmp Commands Virtual LAN Vlan Commands Switching Database CommandsSpanning Tree Commands Switching Statistics Commands Port Configuration CommandsHelp-kbd Console CommandsBanner LogoutSys-stat System CommandsSet-passwd Cold-reset Warm-resetGet-stst-level Set-stst-levelSet-line-slip Init-nvramGet-sw-file Set-sw-fileGet-tftp-srvr Set-rsw-fileSet-tftp-srvr Sw-dnldIP configuration IP CommandsSet-bootp Get-bootpSet-ip Set-ip-confSet-slip Get-slip-confSet-slip-conf Get-gatewPing Ping CommandsPing-stop Stops the active ping process. You can also press cCGet-arp-tbl Address Resolution Protocol ARP CommandsAdd-arp-entry Del-arp-entrySnmp community strings Snmp CommandsGet-comm Set-commGet-auth Snmp trap message commandsSet-auth Get-trapsAdd-trap Switching Database CommandsDel-trap Removes a station from the trap tableGet-lt-entry Database control commandsFF-FF-FF-FF-FF-FF Get-lt-16Del-lt-entry Find-lt-addrDel-lt-addr Add-lt-entrySet-lt-age Custom filteringGet-lt-age Add-cf-entry Get-lt-filterDel-cf-entry Vlan CommandsGet-nv-cftbl Displays the custom filter table stored in NvramGet-vbc-matrix Get-con-matrixDel-vbc-domain Set-vbc-domainGet-vbc-tbl Set-sec-vlanDisplays the table of defined SVLANs Get-svlan-tblSet-mon-port MonitorExample Spanning Tree CommandsGet-st-bcfg Get-stpSet-stp Displays the spanning tree state for all ports Get-st-pcfgGet-st-syscfg Set-br-hellot Set-br-prioSet-br-maxage Set-prt-prio Set-br-fwdelSet-prt-enb Set-prt-pcostUse these commands to configure and display port settings Port Configuration CommandsDisplays the current port configuration Get-port-cfgSet-port-dplex Statistics CommandsSet-speed-sel Set-port-fctrlGet-colls-cnt Get-eth-cntGet-sdist-cnt Get-rmon-cntDisplays the Rmon statistics packet size histogram for port Get-br-cnt2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Troubleshooting Flow Control ProblemsIntel Express 10/100 Fast Ethernet Switch System Default ConfigurationPorts Not installed see Accessories on nextConsole Manager Spanning treeFeatures SpecificationsAccessories Status Indicators per portBoot and Configuration General IndicatorsConnector Interfaces Maximum Cabling DistancesPower Cord Specifications Electrical SpecificationsElectromagnetic Emissions and Safety Agency Approval AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2ASnmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Displaying current state, 44 enabling or disabling IndexGet-bootpcommand Get-authcommandDatabase, switching Control commandsGet-slipcommand Get-port-cfgcommand, 22Get-stpcommand Get-trapscommandMIB Set-commcommandXmt Transmit LED Set-slipcommandSet-stpcommand World Wide Web & Internet FTP Intel BBS Troubleshooting Software updates Installation notesHow to access