Intel 10/100 manual Get-stst-level, Set-stst-level, Warm-reset, Cold-reset, Get-last-err

Page 43

C H A P T E R 3

Intel Express 10/100 Fast Ethernet Switch

The screen displays the following information:

•SNMP agent software version and release date.

•Device SNMP object ID.

•Device MAC address.

•System uptime (in 1/100 of a second) and in days, hours, minutes, and seconds.

•Port description and status. Ports 9 through 12 are labeled as “missing” unless you have optional media adapters installed.

get-stst-level

Displays the self-test level set by the set-stst-levelcommand.

set-stst-level

set-stst-level {noneshortlong}

Changes the self-test level. The switch performs a self-test each time you reset it with the cold-resetcommand or when you cycle the power. The default is none.

warm-reset

Resets the SNMP agent software without resetting the switch (it doesn’t disconnect existing connections). The switch configuration is loaded from the values saved in NVRAM. This command also resets the statistics counters.

cold-reset

Performs a cold reset, which is the same as turning the power off then on again. Any existing connections are lost and the statistics counters are reset.

get-last-err

Displays the most recent system failure, if any, for diagnostic purposes.

SYS_console>get-last-err

System information since the last hardware reset

————————————————————————

Software resets number : 0

The system never encountered a fatal error

40

Image 43

Contents User Guide First edition Contents Chapter Troubleshooting Check the LEDs for power and links Connect the network devices to the switchNext steps Optional Press Eand log into the Console Manager Baud Data bits No parity Stop bit Xon/Xoff flow controlOverview TopologyIntel Express 10/100 Fast Ethernet Switch Installation and SetupRcv Using the SwitchPort status LEDs XmtLink Management status LEDsUTP requirements Cabling RequirementsFiber optic requirements NIC RJ-45 MDI Straight-through vs. crossover cablesDetermining which cable to use Configuring the mixed 10 Mbps workgroup environment Typical ConfigurationsConfiguration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches General rule for Repeater count limitationsOne repeater hop for Configuring Accessing the Console Manager remotely Accessing the Console ManagerEntering commands Using the Console ManagerMeans you can type one of the following Vlan Console Manager command groups Sample Console Manager Session Procedures using this diagramSet the IP configuration. Type the command Configuring the Snmp agent for IPCommands used To configure the Snmp agentTo configure a port for full duplex Configuring a port for full duplexRecommended environments To create an Svlan Creating Virtual LANs VLANsTo create a VBD Create the two SVLANs. Type the commandsMonitoring traffic To check traffic on a port Detecting speed mismatches Detecting faulty adapters or hub portsDetecting bad or poor quality cable Detecting congested segmentsStatistic Definitions Configuring and Managing the Switch Reference Group to display commands relevant to that groupConsole Commands Console Command-line SummarySystem Commands IP Commands Snmp Commands Virtual LAN Vlan Commands Switching Database CommandsSpanning Tree Commands Switching Statistics Commands Port Configuration CommandsLogout Console CommandsHelp-kbd BannerSet-passwd System CommandsSys-stat Set-stst-level Warm-resetCold-reset Get-stst-levelSet-sw-file Init-nvramSet-line-slip Get-sw-fileSw-dnld Set-rsw-fileGet-tftp-srvr Set-tftp-srvrIP configuration IP CommandsSet-ip-conf Get-bootpSet-bootp Set-ipGet-gatew Get-slip-confSet-slip Set-slip-confStops the active ping process. You can also press cC Ping CommandsPing Ping-stopDel-arp-entry Address Resolution Protocol ARP CommandsGet-arp-tbl Add-arp-entrySet-comm Snmp CommandsSnmp community strings Get-commGet-traps Snmp trap message commandsGet-auth Set-authRemoves a station from the trap table Switching Database CommandsAdd-trap Del-trapGet-lt-entry Database control commandsFF-FF-FF-FF-FF-FF Get-lt-16Add-lt-entry Find-lt-addrDel-lt-entry Del-lt-addrGet-lt-age Custom filteringSet-lt-age Add-cf-entry Get-lt-filterDisplays the custom filter table stored in Nvram Vlan CommandsDel-cf-entry Get-nv-cftblGet-vbc-matrix Get-con-matrixSet-sec-vlan Set-vbc-domainDel-vbc-domain Get-vbc-tblMonitor Get-svlan-tblDisplays the table of defined SVLANs Set-mon-portExample Spanning Tree CommandsSet-stp Get-stpGet-st-bcfg Get-st-syscfg Get-st-pcfgDisplays the spanning tree state for all ports Set-br-maxage Set-br-prioSet-br-hellot Set-prt-pcost Set-br-fwdelSet-prt-prio Set-prt-enbGet-port-cfg Port Configuration CommandsUse these commands to configure and display port settings Displays the current port configurationSet-port-fctrl Statistics CommandsSet-port-dplex Set-speed-selGet-colls-cnt Get-eth-cntGet-br-cnt Get-rmon-cntGet-sdist-cnt Displays the Rmon statistics packet size histogram for port2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Troubleshooting Flow Control ProblemsIntel Express 10/100 Fast Ethernet Switch System Default ConfigurationSpanning tree Not installed see Accessories on nextPorts Console ManagerStatus Indicators per port SpecificationsFeatures AccessoriesMaximum Cabling Distances General IndicatorsBoot and Configuration Connector InterfacesAC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2A Electrical SpecificationsPower Cord Specifications Electromagnetic Emissions and Safety Agency ApprovalSnmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Displaying current state, 44 enabling or disabling IndexControl commands Get-authcommandGet-bootpcommand Database, switchingGet-trapscommand Get-port-cfgcommand, 22Get-slipcommand Get-stpcommandMIB Set-commcommandSet-stpcommand Set-slipcommandXmt Transmit LED How to access Troubleshooting Software updates Installation notesWorld Wide Web & Internet FTP Intel BBS