Intel 10/100 manual System Commands, Set-passwd, Sys-stat

Page 42

C H A P T E R 3 Console Command Reference

set-passwd

Changes the console password. The system first prompts you for the old password. You then type a new password and retype it for verification. Passwords never appear on the screen.

SYS_console> set-passwd

Enter old password:

Enter new password:

Enter new password again:

CLI running password changed

CLI password change in the NVRAM OK

If you enter the old password incorrectly or don’t verify the new password correctly, the password isn’t changed.

System Commands

sys-stat

Displays general status information about the switch and its SNMP agent hardware and software:

SYS_console>sys-stat

Intel Express 10/100 Fast Ethernet Switch

SNMP Agent Software - Version <version>

SNMP Object ID is : < .1.3.6.1.4.1.629.1.1.3 >

System MAC Address : 00-A0-C9-00-20-D9

Switching Data Base Size : 4096 entries

Total uptime(hundredths of seconds ): 111151888

Total uptime(days, hh:mm:ss format): 12 days, 20:45:18.88

i/f 1 -- description [ Port 1 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 2 -- description [ Port 2 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 3 -- description [ Port 3 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 4 -- description [ Port 4 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 5 -- description [ Port 5 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 6 -- description [ Port 6 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 7 -- description [ Port 7 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 8 -- description [ Port 8 - 10/100 BaseTx Ethernet Port ] -- status [up] i/f 9 -- description [ Port 9 - missing ] -- status [DOWN]

i/f 10 -- description [ Port 10 - missing ] -- status [DOWN] i/f 11 -- description [ Port 11 - missing ] -- status [DOWN] i/f 12 -- description [ Port 12 - missing ] -- status [DOWN]

39

Image 42

Contents User Guide First edition Contents Chapter Troubleshooting Connect the network devices to the switch Check the LEDs for power and linksNext steps Optional Baud Data bits No parity Stop bit Xon/Xoff flow control Press Eand log into the Console ManagerTopology OverviewInstallation and Setup Intel Express 10/100 Fast Ethernet SwitchXmt Using the SwitchPort status LEDs RcvManagement status LEDs LinkCabling Requirements UTP requirementsFiber optic requirements Straight-through vs. crossover cables NIC RJ-45 MDIDetermining which cable to use Typical Configurations Configuring the mixed 10 Mbps workgroup environmentConfiguration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches Repeater count limitations General rule forOne repeater hop for Configuring Accessing the Console Manager Accessing the Console Manager remotelyUsing the Console Manager Entering commandsMeans you can type one of the following Vlan Console Manager command groups Procedures using this diagram Sample Console Manager SessionTo configure the Snmp agent Configuring the Snmp agent for IPCommands used Set the IP configuration. Type the commandConfiguring a port for full duplex To configure a port for full duplexRecommended environments Creating Virtual LANs VLANs To create an SvlanCreate the two SVLANs. Type the commands To create a VBDMonitoring traffic To check traffic on a port Detecting congested segments Detecting faulty adapters or hub portsDetecting bad or poor quality cable Detecting speed mismatchesStatistic Definitions Configuring and Managing the Switch Group to display commands relevant to that group ReferenceConsole Command-line Summary Console CommandsSystem Commands IP Commands Snmp Commands Switching Database Commands Virtual LAN Vlan CommandsSpanning Tree Commands Port Configuration Commands Switching Statistics CommandsBanner Console CommandsHelp-kbd LogoutSystem Commands Set-passwdSys-stat Get-stst-level Warm-resetCold-reset Set-stst-levelGet-sw-file Init-nvramSet-line-slip Set-sw-fileSet-tftp-srvr Set-rsw-fileGet-tftp-srvr Sw-dnldIP Commands IP configurationSet-ip Get-bootpSet-bootp Set-ip-confSet-slip-conf Get-slip-confSet-slip Get-gatewPing-stop Ping CommandsPing Stops the active ping process. You can also press cCAdd-arp-entry Address Resolution Protocol ARP CommandsGet-arp-tbl Del-arp-entryGet-comm Snmp CommandsSnmp community strings Set-commSet-auth Snmp trap message commandsGet-auth Get-trapsDel-trap Switching Database CommandsAdd-trap Removes a station from the trap tableDatabase control commands Get-lt-entryGet-lt-16 FF-FF-FF-FF-FF-FFDel-lt-addr Find-lt-addrDel-lt-entry Add-lt-entryCustom filtering Get-lt-ageSet-lt-age Get-lt-filter Add-cf-entryGet-nv-cftbl Vlan CommandsDel-cf-entry Displays the custom filter table stored in NvramGet-con-matrix Get-vbc-matrixGet-vbc-tbl Set-vbc-domainDel-vbc-domain Set-sec-vlanSet-mon-port Get-svlan-tblDisplays the table of defined SVLANs MonitorSpanning Tree Commands ExampleGet-stp Set-stpGet-st-bcfg Get-st-pcfg Get-st-syscfgDisplays the spanning tree state for all ports Set-br-prio Set-br-maxageSet-br-hellot Set-prt-enb Set-br-fwdelSet-prt-prio Set-prt-pcostDisplays the current port configuration Port Configuration CommandsUse these commands to configure and display port settings Get-port-cfgSet-speed-sel Statistics CommandsSet-port-dplex Set-port-fctrlGet-eth-cnt Get-colls-cntDisplays the Rmon statistics packet size histogram for port Get-rmon-cntGet-sdist-cnt Get-br-cnt2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Flow Control Problems TroubleshootingIntel Express 10/100 Fast Ethernet Switch Default Configuration SystemConsole Manager Not installed see Accessories on nextPorts Spanning treeAccessories SpecificationsFeatures Status Indicators per portConnector Interfaces General IndicatorsBoot and Configuration Maximum Cabling DistancesElectromagnetic Emissions and Safety Agency Approval Electrical SpecificationsPower Cord Specifications AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2ASnmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Index Displaying current state, 44 enabling or disablingDatabase, switching Get-authcommandGet-bootpcommand Control commandsGet-stpcommand Get-port-cfgcommand, 22Get-slipcommand Get-trapscommandSet-commcommand MIBSet-slipcommand Set-stpcommandXmt Transmit LED Troubleshooting Software updates Installation notes How to accessWorld Wide Web & Internet FTP Intel BBS