Intel 10/100 manual Specifications, Features, Accessories, Network Management

Page 80

A p p e n d i x

A Technical Information

Specifications

Features

Buffer size: 64 Kbytes per port, 512 Kbytes total

Architecture: Store and forward for complete runt and error filtering on all packets. Flow control prevents packet loss.

MAC addresses supported: 4096 entries

Switching database: Transparent, automatic self-learning at full wire speed. Cache aging time manageable. Custom filtering by hardware address and port.

Accessories

Two-port 100BASE-TX expansion module (Intel order code ES101MATX)

Two-port 100BASE-FX expansion module (Intel order code ES101MAFX)

Redundant power supply (RPS) connector. RPS must be purchased separately.

LANDesk Network Manager (Intel order code EC100SNMP). Network Manager is a Windows-based SNMP network management system designed to manage Intel hubs and switches.

Network Management

In-band and out-of-band SNMP with MIB II, private MIB and out-of- band serial console support.

Status Indicators (per port)

Displays Link, Transmit, Receive, Full Duplex/Collision, Flow Control, Speed (10 or 100 Mbps).

77

Image 80

Contents User Guide First edition Contents Chapter Troubleshooting Next steps Optional Connect the network devices to the switchCheck the LEDs for power and links Baud Data bits No parity Stop bit Xon/Xoff flow control Press Eand log into the Console ManagerTopology OverviewInstallation and Setup Intel Express 10/100 Fast Ethernet SwitchUsing the Switch Port status LEDsXmt RcvManagement status LEDs LinkFiber optic requirements Cabling RequirementsUTP requirements Straight-through vs. crossover cables NIC RJ-45 MDIDetermining which cable to use Typical Configurations Configuring the mixed 10 Mbps workgroup environmentConfiguration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches One repeater hop for Repeater count limitationsGeneral rule for Configuring Accessing the Console Manager Accessing the Console Manager remotelyMeans you can type one of the following Using the Console ManagerEntering commands Vlan Console Manager command groups Procedures using this diagram Sample Console Manager SessionConfiguring the Snmp agent for IP Commands usedTo configure the Snmp agent Set the IP configuration. Type the commandRecommended environments Configuring a port for full duplexTo configure a port for full duplex Creating Virtual LANs VLANs To create an SvlanCreate the two SVLANs. Type the commands To create a VBDMonitoring traffic To check traffic on a port Detecting faulty adapters or hub ports Detecting bad or poor quality cableDetecting congested segments Detecting speed mismatchesStatistic Definitions Configuring and Managing the Switch Group to display commands relevant to that group ReferenceSystem Commands Console Command-line SummaryConsole Commands IP Commands Snmp Commands Switching Database Commands Virtual LAN Vlan CommandsSpanning Tree Commands Port Configuration Commands Switching Statistics CommandsConsole Commands Help-kbdBanner LogoutSys-stat System CommandsSet-passwd Warm-reset Cold-resetGet-stst-level Set-stst-levelInit-nvram Set-line-slipGet-sw-file Set-sw-fileSet-rsw-file Get-tftp-srvrSet-tftp-srvr Sw-dnldIP Commands IP configurationGet-bootp Set-bootpSet-ip Set-ip-confGet-slip-conf Set-slipSet-slip-conf Get-gatewPing Commands PingPing-stop Stops the active ping process. You can also press cCAddress Resolution Protocol ARP Commands Get-arp-tblAdd-arp-entry Del-arp-entrySnmp Commands Snmp community stringsGet-comm Set-commSnmp trap message commands Get-authSet-auth Get-trapsSwitching Database Commands Add-trapDel-trap Removes a station from the trap tableDatabase control commands Get-lt-entryGet-lt-16 FF-FF-FF-FF-FF-FFFind-lt-addr Del-lt-entryDel-lt-addr Add-lt-entrySet-lt-age Custom filteringGet-lt-age Get-lt-filter Add-cf-entryVlan Commands Del-cf-entryGet-nv-cftbl Displays the custom filter table stored in NvramGet-con-matrix Get-vbc-matrixSet-vbc-domain Del-vbc-domainGet-vbc-tbl Set-sec-vlanGet-svlan-tbl Displays the table of defined SVLANsSet-mon-port MonitorSpanning Tree Commands ExampleGet-st-bcfg Get-stpSet-stp Displays the spanning tree state for all ports Get-st-pcfgGet-st-syscfg Set-br-hellot Set-br-prioSet-br-maxage Set-br-fwdel Set-prt-prioSet-prt-enb Set-prt-pcostPort Configuration Commands Use these commands to configure and display port settingsDisplays the current port configuration Get-port-cfgStatistics Commands Set-port-dplexSet-speed-sel Set-port-fctrlGet-eth-cnt Get-colls-cntGet-rmon-cnt Get-sdist-cntDisplays the Rmon statistics packet size histogram for port Get-br-cnt2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Flow Control Problems TroubleshootingIntel Express 10/100 Fast Ethernet Switch Default Configuration SystemNot installed see Accessories on next PortsConsole Manager Spanning treeSpecifications FeaturesAccessories Status Indicators per portGeneral Indicators Boot and ConfigurationConnector Interfaces Maximum Cabling DistancesElectrical Specifications Power Cord SpecificationsElectromagnetic Emissions and Safety Agency Approval AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2ASnmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Index Displaying current state, 44 enabling or disablingGet-authcommand Get-bootpcommandDatabase, switching Control commandsGet-port-cfgcommand, 22 Get-slipcommandGet-stpcommand Get-trapscommandSet-commcommand MIBXmt Transmit LED Set-slipcommandSet-stpcommand World Wide Web & Internet FTP Intel BBS Troubleshooting Software updates Installation notesHow to access