Intel 10/100 manual General Indicators, Boot and Configuration, Connector Interfaces, Mounting

Page 81

A p p e n d i x

A Intel Express 10/100 Fast Ethernet Switch

General Indicators

Displays Management activity, SNMP presence, power supply status, device failure detection.

Boot and Configuration

NVRAM configuration loaded on power up and fully downloadable. Firmware local or remote downloadable. BOOTP supported.

Connector Interfaces

UTP/STP RJ-45 (MDI-X pin configuration; MDI or MDI-X for port 1) RS232

SC fiber optic (on optional 100BASE-FX media adapter)

Maximum Cabling Distances

Switch to switch or switch to NIC: Category 5 UTP: 328 feet (100 meters)

62.5/125µ multimode fiber: 1.2 miles (2 kilometers) at full duplex 1351 feet (412 meters) at half duplex

Switch to repeater:

Category 5 UTP: 328 feet (100 meters)

62.5/125µ multimode fiber: 525 feet (160 meters)

Standards Supported

10BASE-T

100BASE-TX, 100BASE-FX Fast Ethernet (IEEE 802.3u) FDSE (Full Duplex Switched Ethernet)

Spanning Tree (IEEE 802.1d)

Internet Hosts (RFC1122/1123) SMI (RFC1155)

SNMP (RFC 1157) MIB (RFC1556) MIB II (RFC 1213) ENET MIB (RFC1398) Bridge MIB (RFC1493) RMON (RFC1757)

UDP/IP (RFC768/950/1071/791)

Mounting

Standard 19-inch rack, with mounting brackets 1-inch minimum clearance, sides and back

78

Image 81

Contents User Guide First edition Contents Chapter Troubleshooting Connect the network devices to the switch Check the LEDs for power and linksNext steps Optional Press Eand log into the Console Manager Baud Data bits No parity Stop bit Xon/Xoff flow controlOverview TopologyIntel Express 10/100 Fast Ethernet Switch Installation and SetupPort status LEDs Using the SwitchXmt RcvLink Management status LEDsCabling Requirements UTP requirementsFiber optic requirements NIC RJ-45 MDI Straight-through vs. crossover cablesDetermining which cable to use Configuring the mixed 10 Mbps workgroup environment Typical ConfigurationsConfiguration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches Repeater count limitations General rule forOne repeater hop for Configuring Accessing the Console Manager remotely Accessing the Console ManagerUsing the Console Manager Entering commandsMeans you can type one of the following Vlan Console Manager command groups Sample Console Manager Session Procedures using this diagramCommands used Configuring the Snmp agent for IPTo configure the Snmp agent Set the IP configuration. Type the commandConfiguring a port for full duplex To configure a port for full duplexRecommended environments To create an Svlan Creating Virtual LANs VLANsTo create a VBD Create the two SVLANs. Type the commandsMonitoring traffic To check traffic on a port Detecting bad or poor quality cable Detecting faulty adapters or hub portsDetecting congested segments Detecting speed mismatchesStatistic Definitions Configuring and Managing the Switch Reference Group to display commands relevant to that groupConsole Command-line Summary Console CommandsSystem Commands IP Commands Snmp Commands Virtual LAN Vlan Commands Switching Database CommandsSpanning Tree Commands Switching Statistics Commands Port Configuration CommandsHelp-kbd Console CommandsBanner LogoutSystem Commands Set-passwdSys-stat Cold-reset Warm-resetGet-stst-level Set-stst-levelSet-line-slip Init-nvramGet-sw-file Set-sw-fileGet-tftp-srvr Set-rsw-fileSet-tftp-srvr Sw-dnldIP configuration IP CommandsSet-bootp Get-bootpSet-ip Set-ip-confSet-slip Get-slip-confSet-slip-conf Get-gatewPing Ping CommandsPing-stop Stops the active ping process. You can also press cCGet-arp-tbl Address Resolution Protocol ARP CommandsAdd-arp-entry Del-arp-entrySnmp community strings Snmp CommandsGet-comm Set-commGet-auth Snmp trap message commandsSet-auth Get-trapsAdd-trap Switching Database CommandsDel-trap Removes a station from the trap tableGet-lt-entry Database control commandsFF-FF-FF-FF-FF-FF Get-lt-16Del-lt-entry Find-lt-addrDel-lt-addr Add-lt-entryCustom filtering Get-lt-ageSet-lt-age Add-cf-entry Get-lt-filterDel-cf-entry Vlan CommandsGet-nv-cftbl Displays the custom filter table stored in NvramGet-vbc-matrix Get-con-matrixDel-vbc-domain Set-vbc-domainGet-vbc-tbl Set-sec-vlanDisplays the table of defined SVLANs Get-svlan-tblSet-mon-port MonitorExample Spanning Tree CommandsGet-stp Set-stpGet-st-bcfg Get-st-pcfg Get-st-syscfgDisplays the spanning tree state for all ports Set-br-prio Set-br-maxageSet-br-hellot Set-prt-prio Set-br-fwdelSet-prt-enb Set-prt-pcostUse these commands to configure and display port settings Port Configuration CommandsDisplays the current port configuration Get-port-cfgSet-port-dplex Statistics CommandsSet-speed-sel Set-port-fctrlGet-colls-cnt Get-eth-cntGet-sdist-cnt Get-rmon-cntDisplays the Rmon statistics packet size histogram for port Get-br-cnt2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Troubleshooting Flow Control ProblemsIntel Express 10/100 Fast Ethernet Switch System Default ConfigurationPorts Not installed see Accessories on nextConsole Manager Spanning treeFeatures SpecificationsAccessories Status Indicators per portBoot and Configuration General IndicatorsConnector Interfaces Maximum Cabling DistancesPower Cord Specifications Electrical SpecificationsElectromagnetic Emissions and Safety Agency Approval AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2ASnmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Displaying current state, 44 enabling or disabling IndexGet-bootpcommand Get-authcommandDatabase, switching Control commandsGet-slipcommand Get-port-cfgcommand, 22Get-stpcommand Get-trapscommandMIB Set-commcommandSet-slipcommand Set-stpcommandXmt Transmit LED Troubleshooting Software updates Installation notes How to accessWorld Wide Web & Internet FTP Intel BBS