Intel 10/100 Get-slip-conf, Set-slip-conf, Get-gatew, Set-gatew, Get-def-ttl, Set-def-ttl

Page 48

C H A P T E R 3 Console Command Reference

get-slip-conf

Displays the current SLIP configuration.

set-slip

set-slip <IPaddress>

Sets the SLIP address, which can’t be the same as the IP address.

set-slip-conf

set-slip-conf <IPaddress> <netmask> <broadcast>

Sets the SLIP configuration. The arguments are the same as

set-ip-conf.

get-gatew

Displays the default gateway. Use this default router when accessing a different IP network.

set-gatew

set-gatew <IPaddress>

Sets the default gateway IP address, which specifies the router used to access a different IP network. The default value for this setting is 0.0.0.0 (no gateway). You can also set the default gateway using the

set-ip-conf command.

SYS_console> set-gatew 192.1.1.255

Device Default Gateway change in the NVRAM OK Device Default Gateway changed to : 192.1.1.255 SYS_console> get-gatew

Device default gateway address is: 192.001.001.255

get-def-ttl

Displays the default IP time-to-live (TTL) value. This value (from 1 to 255) is the number of routers a frame can go through before being dropped. The default is 255.

set-def-ttl

set-def-ttl <number>

Modifies the default TTL value, from 1 to 255 router hops allowed.

45

Image 48

Contents User Guide First edition Contents Chapter Troubleshooting Connect the network devices to the switch Check the LEDs for power and linksNext steps Optional Baud Data bits No parity Stop bit Xon/Xoff flow control Press Eand log into the Console ManagerTopology OverviewInstallation and Setup Intel Express 10/100 Fast Ethernet SwitchUsing the Switch Port status LEDsXmt RcvManagement status LEDs LinkCabling Requirements UTP requirementsFiber optic requirements Straight-through vs. crossover cables NIC RJ-45 MDIDetermining which cable to use Typical Configurations Configuring the mixed 10 Mbps workgroup environmentConfiguration guidelines A P T E R 1 Intel Express 10/100 Fast Ethernet Switch Full duplex and flow control between Express 10/100 switches Repeater count limitations General rule forOne repeater hop for Configuring Accessing the Console Manager Accessing the Console Manager remotelyUsing the Console Manager Entering commandsMeans you can type one of the following Vlan Console Manager command groups Procedures using this diagram Sample Console Manager SessionConfiguring the Snmp agent for IP Commands usedTo configure the Snmp agent Set the IP configuration. Type the commandConfiguring a port for full duplex To configure a port for full duplexRecommended environments Creating Virtual LANs VLANs To create an SvlanCreate the two SVLANs. Type the commands To create a VBDMonitoring traffic To check traffic on a port Detecting faulty adapters or hub ports Detecting bad or poor quality cableDetecting congested segments Detecting speed mismatchesStatistic Definitions Configuring and Managing the Switch Group to display commands relevant to that group ReferenceConsole Command-line Summary Console CommandsSystem Commands IP Commands Snmp Commands Switching Database Commands Virtual LAN Vlan CommandsSpanning Tree Commands Port Configuration Commands Switching Statistics CommandsConsole Commands Help-kbdBanner LogoutSystem Commands Set-passwdSys-stat Warm-reset Cold-resetGet-stst-level Set-stst-levelInit-nvram Set-line-slipGet-sw-file Set-sw-file Set-rsw-file Get-tftp-srvr Set-tftp-srvr Sw-dnldIP Commands IP configurationGet-bootp Set-bootpSet-ip Set-ip-confGet-slip-conf Set-slipSet-slip-conf Get-gatewPing Commands PingPing-stop Stops the active ping process. You can also press cCAddress Resolution Protocol ARP Commands Get-arp-tblAdd-arp-entry Del-arp-entrySnmp Commands Snmp community stringsGet-comm Set-commSnmp trap message commands Get-authSet-auth Get-trapsSwitching Database Commands Add-trapDel-trap Removes a station from the trap tableDatabase control commands Get-lt-entryGet-lt-16 FF-FF-FF-FF-FF-FFFind-lt-addr Del-lt-entryDel-lt-addr Add-lt-entryCustom filtering Get-lt-ageSet-lt-age Get-lt-filter Add-cf-entryVlan Commands Del-cf-entryGet-nv-cftbl Displays the custom filter table stored in NvramGet-con-matrix Get-vbc-matrixSet-vbc-domain Del-vbc-domainGet-vbc-tbl Set-sec-vlanGet-svlan-tbl Displays the table of defined SVLANsSet-mon-port MonitorSpanning Tree Commands ExampleGet-stp Set-stpGet-st-bcfg Get-st-pcfg Get-st-syscfgDisplays the spanning tree state for all ports Set-br-prio Set-br-maxageSet-br-hellot Set-br-fwdel Set-prt-prioSet-prt-enb Set-prt-pcostPort Configuration Commands Use these commands to configure and display port settingsDisplays the current port configuration Get-port-cfgStatistics Commands Set-port-dplexSet-speed-sel Set-port-fctrlGet-eth-cnt Get-colls-cntGet-rmon-cnt Get-sdist-cntDisplays the Rmon statistics packet size histogram for port Get-br-cnt2905033 Bytes Received Get-mgm-brcnt Troubleshooting General Problems Flow Control Problems TroubleshootingIntel Express 10/100 Fast Ethernet Switch Default Configuration SystemNot installed see Accessories on next PortsConsole Manager Spanning treeSpecifications FeaturesAccessories Status Indicators per portGeneral Indicators Boot and ConfigurationConnector Interfaces Maximum Cabling DistancesElectrical Specifications Power Cord SpecificationsElectromagnetic Emissions and Safety Agency Approval AC line frequency 47Hz-63Hz Fuse 100-120V/4A 200-240V/2ASnmp and MIB Support Limited Hardware Warranty Limited Hardware Warranty Europe only Avertissement Warnung Index Displaying current state, 44 enabling or disablingGet-authcommand Get-bootpcommandDatabase, switching Control commandsGet-port-cfgcommand, 22 Get-slipcommandGet-stpcommand Get-trapscommandSet-commcommand MIBSet-slipcommand Set-stpcommandXmt Transmit LED Troubleshooting Software updates Installation notes How to accessWorld Wide Web & Internet FTP Intel BBS