Eiki EIP-1500T owner manual Controlling the Projector by a Computer

Page 30

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control the projector and check the status of the projector.

When connecting to a computer using an RS-232C serial control cable

Computer

RS-232C terminal

2	1

RS-232C serial control cable (cross type, commercially available)

Note

•The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the owner’s manual of the computer for details.

•See “RS-232C Specifications and Command Settings” on page 60 for details.

Info

•Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may damage your computer or projector.

•Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This may damage your computer.

Image 30

Contents EIP-1500T Model No. EIP-1500T Serial No Special Note for Users in the U.K Introduction Information Page Contents Accessories Supplied accessoriesOptional accessory Important Safeguards Rest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Part Names and Functions ProjectorAbout the Indicators on the Projector Lamp indicatorProjector Rear View Refer to Input Terminals and Connectable Main Equipment onRemote Control Usable Range Using the Remote ControlWhen using the remote control Inserting the BatteriesSetup and Projection Quick StartSelect the Input mode Setting Up the Projector Setting Up the ProjectorWhen using a wide screen Screen Size and Projection DistanceProjecting a Reversed Image Projection from behind the ScreenConnections Input Terminals and Connectable Main EquipmentYou may need other cables or connectors not listed below Samples of Cables for ConnectionConnecting to Video Equipment Connecting to Video Equipment DVI output terminal Supplied Connecting to a Computer ComputerConnecting to a Computer Controlling the Projector by a Computer Plug the supplied power cord into the AC socket Connecting the Power CordTurning the Power Off Put Turning the Projector On/OffSwitching the Input Mode Image ProjectionAdjusting the Focus Adjusting the Projected Image SizeUsing the Adjustment Feet Keystone Correction PressHorizontal Keystone Correction Vertical Keystone Correction Align Adjusting the Picture Aspect Ratio Selecting the Picture ModeSwitching the High Bright- ness / High Contrast Mode Press on the remote controlStretch Side BAR Smart Stretch Cinema Zoom Menu Items Following shows the items that can be set in the projectorOptions menu Example Picture menu screen for Input 1 mode Menu icons Using the Menu ScreenMenu Selections Adjustments Press or \ to display the other menu screensPress or \ to adjust the item se- lected To adjust the projected image while viewing itPress or to select the item you want to adjust Single adjustment itemExample Picture menu screen for Menu Selections SettingsInput 1 mode Example Options menu screenSub menu Adjusting the Color Temperature Picture Adjustment Picture menuAdjusting the Image Press or to fine adjust the color temperaturePress or to fine adjust the gamma correction Gamma Correction FunctionEmphasizing the Contrast Picture Mode Function Switching the High Bright- ness/High Contrast ModeExample Picture menu screen for Input 1 mode Special Modes Setting Computer Image Adjustment Fine Sync menuAdjusting the Computer Image Example Fine Sync menu screen for Input 5 Component modeAuto Sync Adjustment Checking the Input SignalExample Fine Sync menu screen for Input 5 RGB mode Using the Options Menu Setting On-screen DisplayChecking the Lamp Life Status Setting the Video System Signal Type SettingEco Mode Selecting a Background ImageAuto Power Off Function Selecting the Menu Screen PositionSelecting the Menu Color Press \ or to select the Lan- guage menu icon Setting the Projection ModeSelecting the On-screen Display Language Press or to select the desired Language, and then pressCleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Abnormal Regarding the Lamp LampReplacing the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord AC socketResetting the Lamp Timer DVI Digital Input Connecting Pin AssignmentsDVI-I Input 5 port 29-pin connector DVI Analog RGB Input DVI Analog Component InputPC control RS-232C Specifications and Command SettingsCommands Communication conditionsComputer Compatibility Chart ComputerTroubleshooting InputSpecifications PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSCDimensions Units inches mmGlossary Index 34,44Memo Deutschland & Österreich CanadaEastern Europe Japan & Worldwide