Eiki EIP-1500T owner manual Setting the Video System, Signal Type Setting

Page 51

Using the “Options” Menu

Setting the Video System

The video input system mode is factory preset to “Auto”; however, a clear picture from the con- nected audio-visual equipment may not be re- ceived, depending on the video signal difference. In that case, switch the video signal.

Menu operation Page 40

Example: “Options” menu screen for INPUT 4 mode

Description of Video Systems

	Selectable items	Description
	PAL	When connected to PAL video equip-
	PAL	ment.
		ment.
	NTSC3.58	When connected to NTSC video
	NTSC3.58	equipment.
		equipment.
	SECAM	When connected to SECAM video
	SECAM	equipment.
		equipment.
	NTSC4.43	When reproducing NTSC signals in PAL
	NTSC4.43	video equipment.
		video equipment.

Note

•The video signal can only be set in INPUT 3, INPUT 4 mode.

•“Auto” cannot be set for PAL-M and PAL-N in- put signals. Select “PAL-M” or “PAL-N” in “Video System” menu for PAL-M and PAL-N input sig- nals.

Signal Type Setting

This function allows you to select the input sig- nal type RGB or Component for INPUT 5.

Menu operation Page 40

Example: “Options” menu screen for INPUT 5 (RGB) mode

Description of Signal Type Settings

Selectable items	Description
RGB	Set when RGB signals are received.
Component	Set when Component signals are
	received.

Note

•You can also select “Signal Type” using on the remote control (only INPUT 5).

48

Image 51

Contents EIP-1500T Model No. EIP-1500T Serial No Special Note for Users in the U.K Introduction Information Page Contents Accessories Supplied accessoriesOptional accessory Important Safeguards Rest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Projector Part Names and FunctionsLamp indicator About the Indicators on the ProjectorRefer to Input Terminals and Connectable Main Equipment on Projector Rear ViewRemote Control Inserting the Batteries Using the Remote ControlWhen using the remote control Usable RangeQuick Start Setup and ProjectionSelect the Input mode Setting Up the Projector Setting Up the ProjectorScreen Size and Projection Distance When using a wide screenProjection from behind the Screen Projecting a Reversed ImageInput Terminals and Connectable Main Equipment ConnectionsSamples of Cables for Connection You may need other cables or connectors not listed belowConnecting to Video Equipment Connecting to Video Equipment DVI output terminal Supplied Computer Connecting to a ComputerConnecting to a Computer Controlling the Projector by a Computer Turning the Projector On/Off Connecting the Power CordTurning the Power Off Put Plug the supplied power cord into the AC socketImage Projection Switching the Input ModeAdjusting the Projected Image Size Adjusting the FocusUsing the Adjustment Feet Keystone Correction PressHorizontal Keystone Correction Vertical Keystone Correction Align Press on the remote control Selecting the Picture ModeSwitching the High Bright- ness / High Contrast Mode Adjusting the Picture Aspect RatioStretch Side BAR Smart Stretch Cinema Zoom Following shows the items that can be set in the projector Menu ItemsOptions menu Press or \ to display the other menu screens Using the Menu ScreenMenu Selections Adjustments Example Picture menu screen for Input 1 mode Menu iconsSingle adjustment item To adjust the projected image while viewing itPress or to select the item you want to adjust Press or \ to adjust the item se- lectedExample Options menu screen Menu Selections SettingsInput 1 mode Example Picture menu screen forSub menu Press or to fine adjust the color temperature Picture Adjustment Picture menuAdjusting the Image Adjusting the Color TemperaturePress or to fine adjust the gamma correction Gamma Correction FunctionEmphasizing the Contrast Picture Mode Function Switching the High Bright- ness/High Contrast ModeExample Picture menu screen for Input 1 mode Example Fine Sync menu screen for Input 5 Component mode Computer Image Adjustment Fine Sync menuAdjusting the Computer Image Special Modes SettingAuto Sync Adjustment Checking the Input SignalExample Fine Sync menu screen for Input 5 RGB mode Using the Options Menu Setting On-screen DisplayChecking the Lamp Life Status Signal Type Setting Setting the Video SystemSelecting a Background Image Eco ModeSelecting the Menu Screen Position Auto Power Off FunctionSelecting the Menu Color Press or to select the desired Language, and then press Setting the Projection ModeSelecting the On-screen Display Language Press \ or to select the Lan- guage menu iconCleaning the exhaust and intake vents MaintenanceCleaning the projector Cleaning the lensMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Abnormal Regarding the Lamp LampReplacing the Lamp AC socket Removing and Installing the Lamp UnitDisconnect the power cord Remove the lamp unit coverResetting the Lamp Timer DVI Analog RGB Input DVI Analog Component Input Connecting Pin AssignmentsDVI-I Input 5 port 29-pin connector DVI Digital InputCommunication conditions RS-232C Specifications and Command SettingsCommands PC controlComputer Computer Compatibility ChartInput TroubleshootingPAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC SpecificationsUnits inches mm DimensionsGlossary 34,44 IndexMemo Japan & Worldwide CanadaEastern Europe Deutschland & Österreich