Eiki EIP-1500T owner manual Using the Adjustment Feet

Page 34

Using the Adjustment Feet

The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector when the screen is located higher than the projector, the screen is inclined or when the installation site is slightly inclined. Install the projector so that it is as perpen- dicular to the screen as possible.

Side View

 

Top View

Lens center

1 Lift the projector to adjust its height while pressing the HEIGHT ADJUST button.

The projector is adjustable up to approxi- mately 12 degrees (6 steps).

When lowering the projector, it may be difficult to move the front adjustment foot because the installation surface is diffi- cult to slide. In this case, pull the pro- jector back slightly and adjust its height.

2 Remove your hands from the HEIGHT ADJUST button of the projector after its height has been finely adjusted.

3 Finely adjust the height and in- clination by turning the rear ad- justment feet.

Note

When adjusting the projected image position, trapezoidal distortion occurs. In this case, see “Keystone Correction” on page 32.

Info

Do not press the HEIGHT ADJUST button when the front adjustment foot comes out without firmly holding the projector.

Do not hold the lens when lifting or lower- ing the projector.

When lowering the projector, be careful not to get your fingers caught in the area be- tween the adjustment foot and the projector.

Front adjustment foot

HEIGHT ADJUST button

Rear adjustment feet

31

Image 34
Contents EIP-1500T Model No. EIP-1500T Serial No Special Note for Users in the U.K Introduction Information Page Contents Supplied accessories AccessoriesOptional accessory Important Safeguards Avoid locations with extremes of tem- perature Rest your eyes occasionallyDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Part Names and Functions ProjectorAbout the Indicators on the Projector Lamp indicatorProjector Rear View Refer to Input Terminals and Connectable Main Equipment onRemote Control Usable Range Using the Remote ControlWhen using the remote control Inserting the BatteriesSetup and Projection Quick StartSelect the Input mode Setting Up the Projector Setting Up the ProjectorWhen using a wide screen Screen Size and Projection DistanceProjecting a Reversed Image Projection from behind the ScreenConnections Input Terminals and Connectable Main EquipmentYou may need other cables or connectors not listed below Samples of Cables for ConnectionConnecting to Video Equipment Connecting to Video Equipment DVI output terminal Supplied Connecting to a Computer ComputerConnecting to a Computer Controlling the Projector by a Computer Plug the supplied power cord into the AC socket Connecting the Power CordTurning the Power Off Put Turning the Projector On/OffSwitching the Input Mode Image ProjectionAdjusting the Focus Adjusting the Projected Image SizeUsing the Adjustment Feet Press Keystone CorrectionHorizontal Keystone Correction Vertical Keystone Correction Align Adjusting the Picture Aspect Ratio Selecting the Picture ModeSwitching the High Bright- ness / High Contrast Mode Press on the remote controlStretch Side BAR Smart Stretch Cinema Zoom Menu Items Following shows the items that can be set in the projectorOptions menu Example Picture menu screen for Input 1 mode Menu icons Using the Menu ScreenMenu Selections Adjustments Press or \ to display the other menu screensPress or \ to adjust the item se- lected To adjust the projected image while viewing itPress or to select the item you want to adjust Single adjustment itemExample Picture menu screen for Menu Selections SettingsInput 1 mode Example Options menu screenSub menu Adjusting the Color Temperature Picture Adjustment Picture menuAdjusting the Image Press or to fine adjust the color temperatureGamma Correction Function Press or to fine adjust the gamma correctionEmphasizing the Contrast Switching the High Bright- ness/High Contrast Mode Picture Mode FunctionExample Picture menu screen for Input 1 mode Special Modes Setting Computer Image Adjustment Fine Sync menuAdjusting the Computer Image Example Fine Sync menu screen for Input 5 Component modeChecking the Input Signal Auto Sync AdjustmentExample Fine Sync menu screen for Input 5 RGB mode Setting On-screen Display Using the Options MenuChecking the Lamp Life Status Setting the Video System Signal Type SettingEco Mode Selecting a Background ImageAuto Power Off Function Selecting the Menu Screen PositionSelecting the Menu Color Press \ or to select the Lan- guage menu icon Setting the Projection ModeSelecting the On-screen Display Language Press or to select the desired Language, and then pressCleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsAbout the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator Abnormal Lamp Regarding the LampReplacing the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord AC socketResetting the Lamp Timer DVI Digital Input Connecting Pin AssignmentsDVI-I Input 5 port 29-pin connector DVI Analog RGB Input DVI Analog Component InputPC control RS-232C Specifications and Command SettingsCommands Communication conditionsComputer Compatibility Chart ComputerTroubleshooting InputSpecifications PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSCDimensions Units inches mmGlossary Index 34,44Memo Deutschland & Österreich CanadaEastern Europe Japan & Worldwide