Eiki EIP-1500T Removing and Installing the Lamp Unit, Disconnect the power cord, AC socket

Page 60

Removing and Installing the Lamp Unit

Warning!

•During projector operation, the lamp unit is very hot. Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury.

Info

•Make sure that you remove the lamp unit by the handle. Do not touch the glass sur- face of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

Optional	Lamp unit
accessory	AH-57201

STANDBY-ON button

1 Press on the projector or on the remote control to put the projector into standby mode.

•Wait until the cooling fan stops.

2 Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3 Remove the lamp unit cover.

AC socket

•Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Hold the tab and slide to- wards the direction of the arrow to re- move the lamp unit cover (2).

1

Tab

2

User service screw (for lamp unit cover)

Tab

57

Image 60

Contents EIP-1500T Model No. EIP-1500T Serial No Special Note for Users in the U.K Introduction Information Page Contents Accessories Supplied accessoriesOptional accessory Important Safeguards Rest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Part Names and Functions ProjectorAbout the Indicators on the Projector Lamp indicatorProjector Rear View Refer to Input Terminals and Connectable Main Equipment onRemote Control Using the Remote Control When using the remote controlUsable Range Inserting the BatteriesSetup and Projection Quick StartSelect the Input mode Setting Up the Projector Setting Up the ProjectorWhen using a wide screen Screen Size and Projection DistanceProjecting a Reversed Image Projection from behind the ScreenConnections Input Terminals and Connectable Main EquipmentYou may need other cables or connectors not listed below Samples of Cables for ConnectionConnecting to Video Equipment Connecting to Video Equipment DVI output terminal Supplied Connecting to a Computer ComputerConnecting to a Computer Controlling the Projector by a Computer Connecting the Power Cord Turning the Power Off PutPlug the supplied power cord into the AC socket Turning the Projector On/OffSwitching the Input Mode Image ProjectionAdjusting the Focus Adjusting the Projected Image SizeUsing the Adjustment Feet Keystone Correction PressHorizontal Keystone Correction Vertical Keystone Correction Align Selecting the Picture Mode Switching the High Bright- ness / High Contrast ModeAdjusting the Picture Aspect Ratio Press on the remote controlStretch Side BAR Smart Stretch Cinema Zoom Menu Items Following shows the items that can be set in the projectorOptions menu Using the Menu Screen Menu Selections AdjustmentsExample Picture menu screen for Input 1 mode Menu icons Press or \ to display the other menu screensTo adjust the projected image while viewing it Press or to select the item you want to adjustPress or \ to adjust the item se- lected Single adjustment itemMenu Selections Settings Input 1 modeExample Picture menu screen for Example Options menu screenSub menu Picture Adjustment Picture menu Adjusting the ImageAdjusting the Color Temperature Press or to fine adjust the color temperaturePress or to fine adjust the gamma correction Gamma Correction FunctionEmphasizing the Contrast Picture Mode Function Switching the High Bright- ness/High Contrast ModeExample Picture menu screen for Input 1 mode Computer Image Adjustment Fine Sync menu Adjusting the Computer ImageSpecial Modes Setting Example Fine Sync menu screen for Input 5 Component modeAuto Sync Adjustment Checking the Input SignalExample Fine Sync menu screen for Input 5 RGB mode Using the Options Menu Setting On-screen DisplayChecking the Lamp Life Status Setting the Video System Signal Type SettingEco Mode Selecting a Background ImageAuto Power Off Function Selecting the Menu Screen PositionSelecting the Menu Color Setting the Projection Mode Selecting the On-screen Display LanguagePress \ or to select the Lan- guage menu icon Press or to select the desired Language, and then pressMaintenance Cleaning the projectorCleaning the lens Cleaning the exhaust and intake ventsMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Abnormal Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover AC socketResetting the Lamp Timer Connecting Pin Assignments DVI-I Input 5 port 29-pin connectorDVI Digital Input DVI Analog RGB Input DVI Analog Component InputRS-232C Specifications and Command Settings CommandsPC control Communication conditionsComputer Compatibility Chart ComputerTroubleshooting InputSpecifications PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSCDimensions Units inches mmGlossary Index 34,44Memo Canada Eastern EuropeDeutschland & Österreich Japan & Worldwide