Eiki LC-XBM31 owner manual Terminal, Direct on, Shut down

Page 49

Setting

Terminal

The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector is switchable for computer input or monitor output. (See page 9) Select Computer 2 or Monitor Out with the Point ▲▼ buttons.

Computer 2 . . computer input

Monitor Out . monitor out

Terminal function is not available when selecting Computer 2 to the input source. Change the input source to the others (Computer 1, and so on) so that the Terminal function will be available. (pp.25, 36, 37)

Power management

For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not operated for a certain period.

Select one of the following options:

Ready

When the lamp has been fully

 

cooled down, the POWER

 

indicator changes to green

 

blinking. In this condition, the

 

projection lamp will be turned on

 

if the input signal is reconnected

 

or any button on the top control or

Shut down

remote control is pressed.

When the lamp has been fully

 

cooled down, the power will be

Off

turned off.

Power management function is

Timer

off.

If the input signal is interrupted

 

and no button is pressed for more

 

than 30 seconds, the timer display

 

with No signal appears. It starts

 

the countdown until the lamp is

 

turned off. Use the Point ▲▼

 

buttons to set the Timer (1~30

 

min).

Note:

Factory default is Ready: 5 min.

Direct on

When this function is set to On, the projector will be automatically turned on just by connecting the AC power cord to a wall outlet.

Note:

Be sure to turn off the projector properly (see “Turning Off the Projector” on page 20). If the projector is turned off in the incorrect sequence, the Direct on function will not work properly.

Power management

Time left before Lamp is off.

49

Image 49
Contents Network Supported Model LC-XBM31Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Installing the Projector in Proper Position Safety InstructionsAir Circulation Moving the ProjectorAC Power Cord for the United States and Canada AC Power Cord RequirementAC Power Cord for the United Kingdom ComplianceFront Part Names and FunctionsBack BottomRear Terminal Part Names and Functions⑤ LAN Connection Terminal Top Control Remote Control Remote Control Operating Range Remote Control Battery InstallationRemote Control Code Menu buttonAdjustable Foot InstallationPositioning the Projector NoteConnecting to a Computer InstallationCables used for connection MIC Connecting to Video EquipmentConnecting to Component Video and RGB Scart Equipment Connecting the AC Power Cord Basic Operation Input signal guidance windowTurning On the Projector Selected Input Source and Lamp ControlBasic Operation What is PIN code?Enter a PIN code PIN Code Input Dialog BoxDirect OFF Function Turning Off the ProjectorRemote Control How to Operate the On-Screen MenuTop Control On-Screen MenuMenu Bar Auto Setup Function Zoom and Focus AdjustmentAuto Setup button Point buttons Keystone CorrectionSound Adjustment Remote Control Operation Timer Timer buttonNo Show button Image buttonComputer Input Remote Control Computer 1 buttonInput Source Selection RGB Computer 1/Computer Computer 2 buttonComputer System Selection Computer InputAuto ModePC adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC adjManual PC Adjustment Mode free ResetStore Image Mode Selection Image Adjustment Screen Size Adjustment Digital zoom Digital zoom +Keystone CeilingInput Source Selection Video, S-video Video InputVideo button Video Video button S-video VideoInput Source Selection Component, RGB Scart 21-pin Video InputInput Menu Component buttonVideo or S-video Auto Video System SelectionComponent Auto AV System Menu Video or S-video AV System Menu ComponentDynamic Color Image Adjust MenuTint Blackboard or ColorboardProgressive Noise reductionStore Menu Screen Menu Note Keystone Setting SettingSetting Menu LanguageAuto setup SettingBackground Logo Logo and Logo PIN code lock settingsDisplay Logo select720p, 1035i, CaptureLogo PIN code lock Change the Logo PIN code lock setting Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code changeDirect on TerminalShut down Stop or Cancel the P-timer via Remote Control Standby modeCount down 00000-18000 At Restart to resume Count up orClosed Caption Code To change the code for the projector To change the code for the remote controlKey lock Security Key lock and PIN code lockPIN code lock Key lockEnter a PIN code Change the PIN code lock settingChange the PIN code Enter a PIN code Change the PIN codeLamp counter reset Video delay controlFan Fan controlFilter counter Factory defaultOff/2000H/3000H/4000H. Note Information Remote ControlInput Source Information Display Projector is shut down and the Warning indicator lights red Maintenance and CleaningNote Then check the matters below Resetting the Filter Counter Maintenance and CleaningFilter counter reset Replacing the FilterCleaning the Projector Cabinet Cleaning the Projection LensAttaching the Lens Cap Reset the lamp counter Lamp ReplacementLamp Handling Precautions Appendix TroubleshootingAppendix Indicator blinks or lights Remote Control doesImage is distorted or runs off PIN code dialog box appearsAppendix Computer Input/Video Input Menu TreeComputer Input Video InputIndicators Indicators and Projector ConditionRed RedDisplay Compatible Computer SpecificationsTechnical Specifications Specifications are subject to change without notice AccessoriesOptional Parts Model NoAttaching the Filter Cover to the Projector PJ Link NoticeTerminal Analog RGB Mini D-sub 15 pin Configurations of TerminalsTX + RX + Horiz. sync. Input/OutputLogo PIN Code Lock No PIN Code Lock NoPIN Code Number Memo Unit mminch DimensionsKT8BE