Eiki LC-XBM31 Image is distorted or runs off, PIN code dialog box appears, At start-up, Not work

Page 65

 

 

Appendix

 

 

 

 

 

 

 

 

 

The image is distorted or runs off.

– Check PC adjust menu or Screen menu and adjust them.

 

 

See pages 30-31, 34-35.

 

 

 

 

 

PIN code dialog box appears

– PIN code lock is being set. Enter a PIN code (the “1234” or numbers

 

at start-up..

you have set). See pages 19, 53-54.

 

 

 

 

 

The Remote Control does

– Check the batteries.

 

not work..

– Make sure no obstruction is between the projector and remote

 

 

control.

 

 

– Make sure you are not too far from the projector when using the

 

 

remote control. Maximum operating range is 16.4'(5 m).

 

 

– Make sure the code of the remote control is conformed to the

 

 

projector’s code. See page 52.

 

 

– Unlock the Key lock function for the remote control function.

 

 

See page 53.

 

 

 

 

 

Indicator blinks or lights.

– Check the status of the projector with referring to "Indicators and

 

 

projector Condition". See page 69.

 

 

 

 

 

The exclamation mark appears

– Your operation is invalid. Operate correctly.

 

on the screen.

 

 

 

 

 

 

Top control does not work.

The top control is not available if the top control is locked at Key lock under Security of SETTING section. See page 53.

Unable to unlock the Logo PIN code lock, Security key lock or Security PIN code lock.

Contact the dealer where you purchased the projector or the service center.

The projector detects an abnormal condition. Unplug the AC power cord and contact the dealer where you purchased the projector or the service center.

appears on the screen

65

Image 65
Contents Network Supported Model LC-XBM31Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Installing the Projector in Proper Position Safety InstructionsAir Circulation Moving the ProjectorAC Power Cord for the United States and Canada AC Power Cord RequirementAC Power Cord for the United Kingdom ComplianceFront Part Names and FunctionsBack Bottom⑤ LAN Connection Terminal Part Names and FunctionsRear Terminal Top Control Remote Control Remote Control Operating Range Remote Control Battery InstallationRemote Control Code Menu buttonAdjustable Foot InstallationPositioning the Projector NoteCables used for connection InstallationConnecting to a Computer MIC Connecting to Video EquipmentConnecting to Component Video and RGB Scart Equipment Connecting the AC Power Cord Basic Operation Input signal guidance windowTurning On the Projector Selected Input Source and Lamp ControlBasic Operation What is PIN code?Enter a PIN code PIN Code Input Dialog BoxDirect OFF Function Turning Off the ProjectorRemote Control How to Operate the On-Screen MenuTop Control On-Screen MenuMenu Bar Auto Setup Function Zoom and Focus AdjustmentAuto Setup button Point buttons Keystone CorrectionSound Adjustment Remote Control Operation Timer Timer buttonNo Show button Image buttonComputer Input Remote Control Computer 1 buttonInput Source Selection RGB Computer 1/Computer Computer 2 buttonComputer System Selection Computer InputAuto ModePC adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC adjManual PC Adjustment Store ResetMode free Image Mode Selection Image Adjustment Screen Size Adjustment Digital zoom Digital zoom +Keystone CeilingInput Source Selection Video, S-video Video InputVideo button Video Video button S-video VideoInput Source Selection Component, RGB Scart 21-pin Video InputInput Menu Component buttonVideo or S-video Auto Video System SelectionComponent Auto AV System Menu Video or S-video AV System Menu ComponentDynamic Color Image Adjust MenuTint Blackboard or ColorboardStore Menu Noise reductionProgressive Screen Menu Note Keystone Setting SettingSetting Menu LanguageAuto setup SettingBackground Logo Logo and Logo PIN code lock settingsDisplay Logo selectLogo PIN code lock Capture720p, 1035i, Change the Logo PIN code lock setting Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code changeShut down TerminalDirect on Stop or Cancel the P-timer via Remote Control Standby modeCount down 00000-18000 At Restart to resume Count up orClosed Caption Code To change the code for the projector To change the code for the remote controlKey lock Security Key lock and PIN code lockPIN code lock Key lockEnter a PIN code Change the PIN code lock settingChange the PIN code Enter a PIN code Change the PIN codeLamp counter reset Video delay controlFan Fan controlOff/2000H/3000H/4000H. Note Factory defaultFilter counter Input Source Information Display Remote ControlInformation Note Then check the matters below Maintenance and CleaningProjector is shut down and the Warning indicator lights red Resetting the Filter Counter Maintenance and CleaningFilter counter reset Replacing the FilterAttaching the Lens Cap Cleaning the Projection LensCleaning the Projector Cabinet Reset the lamp counter Lamp ReplacementLamp Handling Precautions Appendix TroubleshootingAppendix Indicator blinks or lights Remote Control doesImage is distorted or runs off PIN code dialog box appearsAppendix Computer Input/Video Input Menu TreeComputer Input Video InputIndicators Indicators and Projector ConditionRed RedDisplay Compatible Computer SpecificationsTechnical Specifications Specifications are subject to change without notice AccessoriesOptional Parts Model NoAttaching the Filter Cover to the Projector PJ Link NoticeTerminal Analog RGB Mini D-sub 15 pin Configurations of TerminalsTX + RX + Horiz. sync. Input/OutputPIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Unit mminch DimensionsKT8BE