Eiki LC-XBM31 owner manual Input Source Information Display, Remote Control

Page 57

Information

Input Source Information Display

The Information Menu is used for checking the status of the image signal being projected and the operation of the projector.

Direct Operation

Press the INFO. button on the remote control to display

Remote Control

the Information Menu.

 

Menu Operation

Press the Point ▲▼ buttons to select the Information.

The Information Menu is displayed.

See below for displayed information.

INFO. button

Input

 

The selected input source is displayed.

 

H-sync freq.

 

The horizontal frequency of the input signal is

Information Menu

displayed in KHz, or - - - - KHz when no signal.

V-sync freq.

The vertical frequency of the input signal is displayed in Hz, or - - - - Hz when no signal. Numbers of Hz doubles when during Interlace.

Screen

The selected screen size is displayed.

Language

The selected language is displayed.

Lamp status

The selected lamp mode is displayed.

Lamp counter

The cumulative lamp operating time is displayed.

Power management

Off, Ready or Shut down, and Timer are displayed.

Key lock

The selected Key lock icon is displayed.

PIN code lock

Off or On 1 or On 2 is displayed.

Remote control

The selected remote code is displayed.

SERIAL NO.

The serial number of the projector is displayed. The serial number is used to service the projector.

57

Image 57
Contents Network Supported Model LC-XBM31Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Installing the Projector in Proper Position Safety InstructionsAir Circulation Moving the ProjectorAC Power Cord for the United States and Canada AC Power Cord RequirementAC Power Cord for the United Kingdom ComplianceFront Part Names and FunctionsBack BottomPart Names and Functions Rear Terminal⑤ LAN Connection Terminal Top Control Remote Control Remote Control Operating Range Remote Control Battery InstallationRemote Control Code Menu buttonAdjustable Foot InstallationPositioning the Projector NoteInstallation Connecting to a ComputerCables used for connection MIC Connecting to Video EquipmentConnecting to Component Video and RGB Scart Equipment Connecting the AC Power Cord Basic Operation Input signal guidance windowTurning On the Projector Selected Input Source and Lamp ControlBasic Operation What is PIN code?Enter a PIN code PIN Code Input Dialog BoxDirect OFF Function Turning Off the ProjectorRemote Control How to Operate the On-Screen MenuTop Control On-Screen MenuMenu Bar Auto Setup Function Zoom and Focus AdjustmentAuto Setup button Point buttons Keystone CorrectionSound Adjustment Remote Control Operation Timer Timer buttonNo Show button Image buttonComputer Input Remote Control Computer 1 buttonInput Source Selection RGB Computer 1/Computer Computer 2 buttonComputer System Selection Computer InputAuto ModePC adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC adjManual PC Adjustment Reset Mode freeStore Image Mode Selection Image Adjustment Screen Size Adjustment Digital zoom Digital zoom +Keystone CeilingInput Source Selection Video, S-video Video InputVideo button Video Video button S-video VideoInput Source Selection Component, RGB Scart 21-pin Video InputInput Menu Component buttonVideo or S-video Auto Video System SelectionComponent Auto AV System Menu Video or S-video AV System Menu ComponentDynamic Color Image Adjust MenuTint Blackboard or ColorboardNoise reduction ProgressiveStore Menu Screen Menu Note Keystone Setting SettingSetting Menu LanguageAuto setup SettingBackground Logo Logo and Logo PIN code lock settingsDisplay Logo selectCapture 720p, 1035i,Logo PIN code lock Change the Logo PIN code lock setting Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code changeTerminal Direct onShut down Stop or Cancel the P-timer via Remote Control Standby modeCount down 00000-18000 At Restart to resume Count up orClosed Caption Code To change the code for the projector To change the code for the remote controlKey lock Security Key lock and PIN code lockPIN code lock Key lockEnter a PIN code Change the PIN code lock settingChange the PIN code Enter a PIN code Change the PIN codeLamp counter reset Video delay controlFan Fan controlFactory default Filter counterOff/2000H/3000H/4000H. Note Remote Control InformationInput Source Information Display Maintenance and Cleaning Projector is shut down and the Warning indicator lights redNote Then check the matters below Resetting the Filter Counter Maintenance and CleaningFilter counter reset Replacing the FilterCleaning the Projection Lens Cleaning the Projector CabinetAttaching the Lens Cap Reset the lamp counter Lamp ReplacementLamp Handling Precautions Appendix TroubleshootingAppendix Indicator blinks or lights Remote Control doesImage is distorted or runs off PIN code dialog box appearsAppendix Computer Input/Video Input Menu TreeComputer Input Video InputIndicators Indicators and Projector ConditionRed RedDisplay Compatible Computer SpecificationsTechnical Specifications Specifications are subject to change without notice AccessoriesOptional Parts Model NoAttaching the Filter Cover to the Projector PJ Link NoticeTerminal Analog RGB Mini D-sub 15 pin Configurations of TerminalsTX + RX + Horiz. sync. Input/OutputPIN Code Lock No Logo PIN Code Lock NoPIN Code Number Memo Unit mminch DimensionsKT8BE