Eiki LC-XBM31 Configurations of Terminals, Terminal Analog RGB Mini D-sub 15 pin, Tx + Rx +

Page 74

Appendix

Configurations of Terminals

COMPUTER IN 1 / S-VIDEO IN/ COMPONENT IN

Terminal: Analog RGB (Mini D-sub 15 pin)

5 4 3 2 1

10 9 8 7 6

15 14 13 12 11

1Red/Cr/S-C Input

2Green/Y/S-Y Input

3Blue/Cb/--- Input

4-----

5Ground (Horiz.sync.)

6Ground (Red)

7Ground (Green)

8Ground (Blue)

9+5V Power

10Ground (Vert.sync.)

11Ground

12DDC Data

13Horiz. sync. Input/Output (Composite H/V sync.)

14Vert. sync.

15DDC Clock

COMPUTER IN 2/MONITOR OUT (ANALOG)

Terminal: Analog RGB (Mini D-sub 15 pin)

5 4 3 2 1

10 9 8 7 6

15 14 13 12 11

1

Red Input/Output

9

-----

2

Green Input/Output

10

Ground (Vert.sync.)

3

Blue Input/Output

11

-----

4

-----

12

-----

5

Ground (Horiz.sync.)

13

Horiz. sync. Input/Output

6

Ground (Red)

14

Vert. sync.

7

Ground (Green)

15

-----

8

Ground (Blue)

 

 

CONTROL PORT CONNECTOR (D-sub 9 pin)

 

Serial

5

SG

1

-----

6

-----

2

R X D

7

-----

3

T X D

8

-----

4

-----

9

-----

LAN TERMINAL

1

TX +

5

-----

2

TX –

6

RX –

3

RX +

7

-----

4

-----

8

-----

74

Page 73 Page 75
Image 74
Page 73 Page 75
Contents Model LC-XBM31 Network SupportedFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Air Circulation Safety InstructionsInstalling the Projector in Proper Position Moving the ProjectorAC Power Cord for the United Kingdom AC Power Cord RequirementAC Power Cord for the United States and Canada ComplianceBack Part Names and FunctionsFront Bottom⑤ LAN Connection Terminal Part Names and FunctionsRear Terminal Top Control Remote Control Remote Control Code Remote Control Battery InstallationRemote Control Operating Range Menu buttonPositioning the Projector InstallationAdjustable Foot NoteCables used for connection InstallationConnecting to a Computer Connecting to Video Equipment MICConnecting to Component Video and RGB Scart Equipment Connecting the AC Power Cord Turning On the Projector Input signal guidance windowBasic Operation Selected Input Source and Lamp ControlEnter a PIN code What is PIN code?Basic Operation PIN Code Input Dialog BoxTurning Off the Projector Direct OFF FunctionTop Control How to Operate the On-Screen MenuRemote Control On-Screen MenuMenu Bar Auto Setup button Point buttons Zoom and Focus AdjustmentAuto Setup Function Keystone CorrectionSound Adjustment Remote Control Operation No Show button Timer buttonTimer Image buttonInput Source Selection RGB Computer 1/Computer Remote Control Computer 1 buttonComputer Input Computer 2 buttonAuto Computer InputComputer System Selection ModeTo store adjustment parameters Auto PC AdjustmentPC adjust Menu Auto PC adjManual PC Adjustment Store ResetMode free Image Mode Selection Image Adjustment Screen Size Adjustment Keystone Digital zoom +Digital zoom CeilingVideo button Video Video button S-video Video InputInput Source Selection Video, S-video VideoInput Menu Video InputInput Source Selection Component, RGB Scart 21-pin Component buttonComponent Auto Video System SelectionVideo or S-video Auto AV System Menu Video or S-video AV System Menu ComponentDynamic Tint Image Adjust MenuColor Blackboard or ColorboardStore Menu Noise reductionProgressive Screen Menu Note Keystone Setting Menu SettingSetting LanguageSetting Auto setupDisplay Logo Logo and Logo PIN code lock settingsBackground Logo selectLogo PIN code lock Capture720p, 1035i, Enter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code lock setting Logo PIN code changeShut down TerminalDirect on Count down 00000-18000 Standby modeStop or Cancel the P-timer via Remote Control At Restart to resume Count up orClosed Caption To change the code for the remote control Code To change the code for the projectorPIN code lock Security Key lock and PIN code lockKey lock Key lockChange the PIN code Change the PIN code lock settingEnter a PIN code Enter a PIN code Change the PIN codeFan Video delay controlLamp counter reset Fan controlOff/2000H/3000H/4000H. Note Factory defaultFilter counter Input Source Information Display Remote ControlInformation Note Then check the matters below Maintenance and CleaningProjector is shut down and the Warning indicator lights red Filter counter reset Maintenance and CleaningResetting the Filter Counter Replacing the FilterAttaching the Lens Cap Cleaning the Projection LensCleaning the Projector Cabinet Lamp Replacement Reset the lamp counterLamp Handling Precautions Troubleshooting AppendixAppendix Image is distorted or runs off Remote Control doesIndicator blinks or lights PIN code dialog box appearsAppendix Menu Tree Computer Input/Video InputVideo Input Computer InputRed Indicators and Projector ConditionIndicators RedCompatible Computer Specifications DisplayTechnical Specifications Optional Parts AccessoriesSpecifications are subject to change without notice Model NoPJ Link Notice Attaching the Filter Cover to the ProjectorTX + RX + Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin Horiz. sync. Input/OutputPIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Dimensions Unit mminchKT8BE
Top Page Image Contents