Eiki LC-XD25 owner manual Safety Instructions

Page 5

Safety Instructions

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for

example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and car t combination to overturn.

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to ensure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

Do not install the projector near the ventilation duct of air- conditioning equipment.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the projector.

c.If the projector has been exposed to rain or water.

d.If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e.If the projector has been dropped or the cabinet has been damaged.

f. When the projector exhibits a distinct change in performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

NOTE FOR CUSTOMERS IN THE US

Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.

Image 5
Contents Model LC-XD25 Features and Design Table of Contents Risk of Electric Shock Do not Open To the OwnerSafety Instructions Moving the Projector Installing the Projector in Proper PositionAir Circulation Federal Communications Commission Notice ComplianceFront Part Names and FunctionsBack Bottom Air Intake Vent front and bottomRear Terminal Top Control Remote Control Two AA size batteries Remote Control Battery InstallationOperating Range Positioning the Projector InstallationAdjustable Foot Projector side Using the ferrite coreConnecting the AC Power Cord Cables used for connection Connecting to a ComputerConnecting to Video Equipment Connecting to Component Video and RGB Scart Equipment Video / PC selection window Input signal guidance window Selected Input Source and Lamp ModeBasic Operation Turning On the ProjectorPIN Code Input Dialog Box Basic OperationTurning Off the Projector Remote Control How to Operate the On-Screen MenuTop Control On-Screen MenuMenu Bar Keystone Correction Zoom and Focus AdjustmentAuto setup function Remote Control Operation Sound AdjustmentAuto PC button Timer buttonZoom buttons Keystone buttonInput Source Selection Computer InputDirect Operation Source Select MenuSelecting Computer System Manually Computer System SelectionPC System Menu Menu Operation Auto PC Adj Auto PC AdjustmentTo store adjustment parameters Manual PC Adjustment Mode free ResetTo clear adjusted data To store adjusted dataImage Level Selection Image Select Menu icon Image Level Adjustment True Screen Size AdjustmentNormal Custom WideFull Digital zoom + For zooming in and out the imagesDigital zoom Zoom buttonVideo button Video InputInput Source Selection Video Video Component RGB Scart Input Source Selection S-video, Component, RGB Scart 21-pinAuto Video System SelectionAV System Menu Video or S-video AV System Menu ComponentCinema User preset image in the Image Adjust Menu. p.43 Tint ColorProgressive Noise reductionProvide the image at a normal video aspect ratio Setting SettingSetting Menu Language LanguageAuto Keystone Auto setupInput search Display KeystoneBlue back Logo select Logo Logo and Logo PIN code lock settingsCapture Logo select CaptureLogo PIN code lock Logo PIN code lock Dialog Box Logo PIN code lockCeiling Standby modeRear TerminalOn start Remote control PIN code lock Security Key lock and PIN code lock settingsKey lock Change the PIN code Change the PIN code lock settingEnter a PIN code Fan control FanLamp counter Factory defaultClosed Caption Factory default Indicator emits a red light Maintenance and CleaningThen check the matters below Projector is shut down and the WarningAttaching the Lens Cover Cleaning the Air FilterCleaning the Projector Cabinet Cleaning the Projection LensLamp Replacement Reset the lamp replacement counter Order Replacement LampResetting the Lamp Counter Lamp Handling PrecautionsAppendix TroubleshootingShow function is running. see pages 24 Power management function can not work while Freeze or NoIndicator blinks or lights Remote Control does not workExclamation mark appears On the screen Top Control does not workMenu Tree PC AdjustInput SoundScreen Image Select Image AdjustSystem Image Select Setting Indicators Projector Condition Indicators and Projector ConditionFreq Compatible Computer SpecificationsTechnical Specifications Model No AccessoriesOptional Parts Dimensions Configurations of TerminalsService Port Connector Terminal Mini DIN 8-PIN SerialPIN Code Number Memo Logo PIN Code Lock NoEiki International, Inc