Intel 82540EP manual Absolute Maximum Ratings, Recommended Operating Conditions

Page 23

Networking Silicon — 82540EP

4.0Voltage, Temperature, and Timing Specifications

Note: The specification values listed in this section are subject to change without notice. Verify with your local Intel sales office that you have the latest information before finalizing a design.

4.1Absolute Maximum Ratings

Table 1. Absolute Maximum Ratingsa

Symbol	Parameter	Min	Max	Unit

VDD	DC supply voltage	-0.3	7	V
VIN	Input voltage	-1	VDD + 0.3	V
IIN	DC input pin current	-10	10	mA
TSTG	Storage	-40	125	° C
TSTG	temperature	-40	125	° C

a.Maximum ratings are referenced to ground (VSS). Permanent device damage is likely to occur if the ratings in this table are exceeded. These values should not be used as the limits for normal device operations.

4.2Recommended Operating Conditions

Table 2. Recommended Operating Conditionsa					(Sheet 1 of 2)
	Symbol	Parameter	Condition		Min	Typ	Max	Unit

	TOP	Operating			0		70	° C
	TOP	Temperature			0		70	° C

	VIO	VIO Voltage			3		5.25	V
	VIO	Range			3		5.25	V

		Periphery	3.3V ± 10%
	VDD	Voltage	3.3V ± 10%		3	3.3	3.6	V
		Range

Datasheet

17

Image 23

Contents Revision April 82540EP Gigabit Ethernet ControllerDatasheet Date Revision 82540EP Networking Silicon Contents 82540EP Networking Silicon Introduction Acpi LED MdioTX MAC RX MACProduct Code Document ScopeReference Documents 82540EP Networking Silicon Application flexibility for LAN on Motherboard PCI FeaturesMAC Specific Features Features BenefitsHostOffloading PHY Specific FeaturesA server management processor Manageability FeaturesTechnology Features Additional Device FeaturesPCI Bus Interface Signal Type DefinitionsPCI Address, Data and Control Signals Symbol Type Name and FunctionTRDY# STS PARFRAME# STS IRDY# STSError Reporting Signals Arbitration SignalsInterrupt Signal System SignalsSMB Signals Eeprom and Serial Flash Interface SignalsPower Management Signals Impedance Compensation SignalsOther Signals Miscellaneous SignalsLED Signals XTAL2 AnalogXTAL1 Analog Supplies Test Interface SignalsPower Supply Connections Digital SuppliesCTRL15 Control SignalsGround and No Connects GNDRecommended Operating Conditions a Sheet 1 Absolute Maximum RatingsRecommended Operating Conditions Absolute Maximum RatingsaRecommended Operating Conditions a Sheet 2 DC SpecificationsDC Characteristics Power Specifications D0aPower Specifications Complete Subsystem Power Specifications D3coldPower Specifications Dr Uninitialized = V SS O CharacteristicsSymbol Parameter Condition Min Typ Max AC Characteristics Tcyc Timing Specifications PCI Bus InterfaceSymbol Parameter a PCI 66 MHz PCI 33 MHz Units Min Max PCI Bus Interface Clock ParametersPCI Bus Interface Timing Parameters Symbol Parameter PCI 66MHz PCI 33 MHz Units Min MaxVTL Symbol Parameter PCI 66 MHz UnitPCI Bus Interface Timing Measurement Conditions VTHInch max Point 50 pF PinInch max Point 1kΩ 10 pF Rise and Fall Times Link Interface TimingEeprom Interface Date Code Device Identification82540EP Product Name YywwPackage Information DatasheetThermal resistance, junction-to-ambient Thermal SpecificationsThermal Characteristics Symbol Parameter Value at specified airflow m/s UnitsPinout Information Eeprom and Serial Flash Interface Signals Power Management SignalsImpedance Compensation Signals SMB SignalsAnalog Power Signals PHY SignalsTest Interface Signals Digital Power SignalsLanpwrgood Smbclk Grounds and No Connect SignalsSignal Names in Pin Order Sheet 1 Signal Name PinCLKRUN# Smbdata GND Signal Names in Pin Order Sheet 2RST# SMBALRT# M66EN REQ# CBE3#CLK VIO TRDY# Zpcomp Signal Names in Pin Order Sheet 3IRDY# FRAME# CBE2# GND PAR PERR# GNT# Signal Names in Pin Order Sheet 4STOP# INTA# DEVSEL# Zncomp CBE0# PCIAD5 GND PCIAD1 Clkview FLCE# Eesk Signal Names in Pin Order Sheet 5CBE1# Vddo P12 Signal Names in Pin Order Sheet 6PCIAD9 PCIAD7 PCIAD4 PCIAD8 PCIAD6 PCIAD3 PCIAD2 Eecs GND Flso EediC D E F G H J K L M N P Visual Pin Reference