Intel 82540EP manual Analog, XTAL1, XTAL2

Page 20

82540EP — Networking Silicon

3.5

3.5.1PHYCrystalSignals

Symbol	Type	Name and Function

		Crystal One. The Crystal One pin is a 25 MHz +/- 50 ppm input signal. It can be
XTAL1	I	connected to either an oscillator or crystal. If a crystal is used, Crystal Two (XTAL2)
		must also be connected.

XTAL2	O	Crystal Two. Crystal Two is the output of an internal oscillator circuit used to drive a
XTAL2	O	crystal into oscillation. If an external oscillator is used in the design, XTAL2 must be
		disconnected.

3.5.2Analog

	Symbol	Type	Name and Function

	REF	P	Reference. This Reference signal should be connected to VSS through an external
	REF	P	2.49 KΩ resistor.
			2.49 KΩ resistor.

			Media Dependent Interface [0].
			1000BASE-T: In MDI configuration, MDI[0]+/- corresponds to BI_DA+/-, and in MDI-X
			configuration, MDI[0]+/- corresponds to BI_DB+/-.
	MDI[0]+/-	A	100BASE-TX: In MDI configuration, MDI[0]+/- is used for the transmit pair, and in MDI-X
			configuration, MDI[0]+/- is used for the receive pair.
			10BASE-T: In MDI configuration, MDI[0]+/- is used for the transmit pair, and in MDI-X
			configuration, MDI[0]+/- is used for the receive pair.

			Media Dependent Interface [1].
			1000BASE-T: In MDI configuration, MDI[1]+/- corresponds to BI_DB+/-, and in MDI-X
			configuration, MDI[1]+/- corresponds to BI_DA+/-.
	MDI[1]+/-	A	100BASE-TX: In MDI configuration, MDI[1]+/- is used for the receive pair, and in MDI-X
			configuration, MDI[1]+/- is used for the transit pair.
			10BASE-T: In MDI configuration, MDI[1]+/- is used for the receive pair, and in MDI-X
			configuration, MDI[1]+/- is used for the transit pair.

			Media Dependent Interface [2].
			1000BASE-T: In MDI configuration, MDI[2]+/- corresponds to BI_DC+/-, and in MDI-X
	MDI[2]+/-	A	configuration, MDI[2]+/- corresponds to BI_DD+/-.
			100BASE-TX: Unused.
			10BASE-T: Unused.

			Media Dependent Interface [3].
			1000BASE-T: In MDI configuration, MDI[3]+/- corresponds to BI_DD+/-, and in MDI-X
	MDI[3]+/-	A	configuration, MDI[3]+/- corresponds to BI_DC+/-.
			100BASE-TX: Unused.
			10BASE-T: Unused.

14

Datasheet

Image 20

Contents 82540EP Gigabit Ethernet Controller Revision AprilDatasheet Date Revision 82540EP Networking Silicon Contents 82540EP Networking Silicon Introduction Mdio TX MACRX MAC Acpi LEDProduct Code Document ScopeReference Documents 82540EP Networking Silicon PCI Features MAC Specific FeaturesFeatures Benefits Application flexibility for LAN on MotherboardPHY Specific Features HostOffloadingManageability Features A server management processorAdditional Device Features Technology FeaturesSignal Type Definitions PCI Address, Data and Control SignalsSymbol Type Name and Function PCI Bus InterfacePAR FRAME# STSIRDY# STS TRDY# STSArbitration Signals Interrupt SignalSystem Signals Error Reporting SignalsEeprom and Serial Flash Interface Signals Power Management SignalsImpedance Compensation Signals SMB SignalsOther Signals Miscellaneous SignalsLED Signals XTAL2 AnalogXTAL1 Test Interface Signals Power Supply ConnectionsDigital Supplies Analog SuppliesControl Signals Ground and No ConnectsGND CTRL15Absolute Maximum Ratings Recommended Operating ConditionsAbsolute Maximum Ratingsa Recommended Operating Conditions a Sheet 1DC Specifications DC CharacteristicsPower Specifications D0a Recommended Operating Conditions a Sheet 2Power Specifications Complete Subsystem Power Specifications D3coldPower Specifications Dr Uninitialized = V SS O CharacteristicsSymbol Parameter Condition Min Typ Max AC Characteristics Timing Specifications PCI Bus Interface Symbol Parameter a PCI 66 MHz PCI 33 MHz Units Min MaxPCI Bus Interface Clock Parameters TcycSymbol Parameter PCI 66MHz PCI 33 MHz Units Min Max PCI Bus Interface Timing ParametersSymbol Parameter PCI 66 MHz Unit PCI Bus Interface Timing Measurement ConditionsVTH VTLInch max Point 50 pF PinInch max Point 1kΩ 10 pF Rise and Fall Times Link Interface TimingEeprom Interface Device Identification 82540EP Product NameYyww Date CodeDatasheet Package InformationThermal Specifications Thermal CharacteristicsSymbol Parameter Value at specified airflow m/s Units Thermal resistance, junction-to-ambientPinout Information Power Management Signals Impedance Compensation SignalsSMB Signals Eeprom and Serial Flash Interface SignalsPHY Signals Test Interface SignalsDigital Power Signals Analog Power SignalsGrounds and No Connect Signals Signal Names in Pin Order Sheet 1Signal Name Pin Lanpwrgood SmbclkSignal Names in Pin Order Sheet 2 RST# SMBALRT#M66EN REQ# CBE3# CLKRUN# Smbdata GNDCLK VIO TRDY# Zpcomp Signal Names in Pin Order Sheet 3IRDY# FRAME# CBE2# GND PAR PERR# GNT# Signal Names in Pin Order Sheet 4STOP# INTA# DEVSEL# Zncomp CBE0# PCIAD5 GND PCIAD1 Clkview FLCE# Eesk Signal Names in Pin Order Sheet 5CBE1# Signal Names in Pin Order Sheet 6 PCIAD9 PCIAD7 PCIAD4PCIAD8 PCIAD6 PCIAD3 PCIAD2 Eecs GND Flso Eedi Vddo P12Visual Pin Reference C D E F G H J K L M N P