Sanyo Proj05 owner manual What are the rules for IP address assignment?

Page 60

Chapter 5 Appendix

Others

QWhat are the rules for IP address assignment?

AIf the network is constructed with TCP/IP protocol, a unique IP address is required for each piece of network equipment. The following are basic rules of the assign- ment.

Rule1

Do not configure the same IP address to the network equipment in the same network group. Each piece of equipment must be assigned a unique IP address.

If the IP address is set [192.168.x.x], the Subnet Mask should be set [255.255.255.0] for example.

Rule2

The start address [xxx.xxx.xxx.0] and the last address [xxx.xxx.xxx.255] of the IP address must not be assigned to any other equipment. These address numbers are reserved.

Rule3

The IP address must correlate to a network number. If network numbers are different between the equipment, they cannot establish communications each other. In this case, the router is placed in the networks to make the rout- ing.

QCan I control the projector by using the telnet application?

APossible. Please refer to the item "Use of telnet" (☞ p.50 - 51).

QWhat is the MAC address assigned to the projector?

AThe MAC address is displayed in "Network information" menu of the projector (☞ p.16) and in "Information" menu through the web browser (☞ p.44).

60

Image 60

Contents Wired Setting Projector Set-up and Operation Network Set-up and OperationCompliance Federal Communications Commission Notice Safety instructions Table of contents Chapter Features Web Management function +p.31Network specifications of the projector Required operating environment for computersExpression/Abbreviation Use of this manualTrademarks Flow of installation Connect the LAN and set the configurationNetwork Configuration has completed Preparation Setup Procedures Connecting to an Ethernet cable Network configuration Network iconDescription Key pallet Move key Network PIN code Network PIN code screenNetwork factory default Network informationChapter Basic Setting and Operation Login the setting page of the projector LoginEnter the IP address Display of main setting Main setting page in the displaySub menu tab Switches the sub menu tab Main menu SettingHow to use the setting Example of the settingSelect an item by selecting a radio button Select items by ticking on check boxesInitial setting Sets the Network PIN code to login the setting page. +p.23Indicates the model name of the projector Indicates the serial number of the projectorNetwork PIN code setting Network configuration Sets Dhcp configuration ON/OFFMail setting Setting Smtp server and administrator address Setting Smtp authenticationRegistering and deleting E-mail addresses Check / DeleteSetting POP server Error message for sending alert mailExamples Type and contents of alert mail Snmp setting Enter community name to send Trap. Default name is publicPJ information Enter user name of the projector etc. optionalUp to 99,999 hours can be set for the time setting Trap check/deleteClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector Power control and status check Service in needDisplays the status of the projectors power. Refer to next Popup confirmation windowAbout projector condition Status DescriptionControl InputInput signal are listed SystemItem Description Image adjustment Image mode Video ComputerPC adjustment Setting up the projector Screen settingAdjusts the image zoom in and out Adjusts the focus of the imageResets the Screen settings Right buttons to adjust them quicklySetting Default, OFF Remote controlSets on or off the logo display on Screen during the startup. UserVideo delay control....Sets the digital processing Frequency.............When Frame lock is set to AutoInformation InformationItems Description Network Indication of the lamp status Indication of the filter statusStatus Controlling the Projector Chapter Appendix Examples of connection Peer-To-Peer connectionGateway Router installed in the network To another networkUse of telnet ControlUse the IP address assigned to the projector Command Function Web browser setting Active Script/JavaScript enableProxy setting Examples OS/Browsers Windows XP ProfessionalInternet Explorer Proxy setting JavaScript Setting Netscape NavigatorMAC OS X v SafariWhy doesn’t the setting page appear in my web browser? How can I restrict access from the computerHow can I install several projectors? Why am I not receiving E-mail alert messages? TingWhat is the MAC address assigned to the projector? What are the rules for IP address assignment?Can I update the firmware of the projector SO-KE2AL