Sanyo PDG-DXL2000 owner manual Connecting to the LAN line

Page 12

Chapter 2 Setup Procedures

Setting procedures and contents differ depending on the LAN installation location. When installing, consult your system administrator to set up the LAN appropriately.

Connecting to the LAN line

Connect the LAN cable to the LAN connection terminal of the projector.

LAN Connection

Terminal

LAN Cable

* Please use a shielded LAN cable.

ACT Lamp (Orange) Blink orange when the projector is sending or receiving the data.

LINK Lamp (Green) Light green when the projector is connected to the network correctly.

Network configuration

Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to “3. Basic setting and operation” (p.17-30). First, complete the settings described in this chapter before performing steps in “3. Basic setting and opera- tion.”

Setting Procedure

1.Select “LAN mode select” in the Network menu, and press Point 8 or SELECT button.

2.Select similar LAN environment among LAN1, LAN2 and LAN3 with the Point ed but- tons. Then the Menu will disappear, the “Please wait...” message will appear, and switch- ing operation will start. Switching will take a while and the projector’s LINK/ACT Lamp will be on or blink, and after completing the operation, the “Please wait...” message will disappear.

12

Image 12

Contents Wired Setting Projector Set-up and Operation Network Set-up and OperationCompliance Federal Communications Commission NoticeAddress Telephone No 818998-7322Safety instructions Table of contents Chapter Features Web Management function +p.31Network specifications of the projector Required operating environment for computersExpression/Abbreviation Use of this manualTrademarks Flow of installation Connect the LAN and set the configurationNetwork Configuration has completed Preparation Setup Procedures Connecting to the LAN line Description Numerical value is a setting example Network PIN codeNetwork factory default Wired LAN factory default settings Chapter Basic Setting and Operation Login the setting page of the projector LoginEnter the IP address Display of main setting Main setting page in the displaySub menu tab Switches the sub menu tab Main menu SettingHow to use the setting Example of the settingSelect an item by selecting a radio button Select items by ticking on check boxesInitial setting Network PIN code setting PJLink and password settingTo 32 alphanumeric characters can be used for the password Whats PJLink?Network configuration Displays the selected LAN modeSets Dhcp configuration ON/OFF Mail setting Enter e-mail address of administratorEnter Smtp password. up to 63 characters Enter Port number of the Smtp server. from 1 toSetting Smtp server and administrator address Setting Smtp authenticationRegistering and deleting E-mail addresses Setting POP server Error message for sending alert mailExamples Type and contents of alert mail Snmp setting Enter community name to send Trap. Default name is publicPJ information Enter user name of the projector etc. optionalUp to 99,999 hours can be set for the time setting Trap check/deleteClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector Power control and status check Service in needDisplays the status of the projectors power. Refer to next Popup confirmation windowAbout projector condition Status DescriptionControl InputInput signal are listed Input signal are listedSystem Auto is fixed at the Scart inputSound Suppresses the sound. ON, OFFImage adjustment PC adjustment Setting up the projector Screen settingSee the next page for the description of other functions Setting Power Out Sets into the selected power manageMent mode Ready, Shutdown, OFF if Input signal is interrupted and noInformation Items DescriptionIndication of the lamp status StatusControlling the Projector Chapter Appendix Examples of connection Peer-To-Peer connectionTo another network Gateway Router installed in the network Entrance hallUse of telnet ControlUse the IP address assigned to the projector Command Function Web browser setting Active Script/JavaScript enableProxy setting Examples OS/Browsers Windows XP ProfessionalInternet Explorer Proxy setting JavaScript Setting Netscape NavigatorMAC OS X v SafariWhy doesn’t the setting page appear in my web browser? How can I restrict access from the computerHow can I install several projectors? Why cant be turned on/off with web browser? Why am I not receiving E-mail alert messages?Ting What is the MAC address assigned to the projector? What are the rules for IP address assignment?Can I update the firmware of the projector SO-KV8AC