Sanyo PDG-DXL2000 owner manual Command Function

Page 49

Use of telnet

3.When communication is established correctly, the word "PASSWORD:" appears on the window. Type the login password (Network PIN code*2) for the projector and then press "Enter" key on the keyboard. If you do not set up the Network PIN code, just press "Enter" key.

When the word "Hello" is replied, login has been succeeded.

*The password "1234" is used for the example.

4.Type the commands, refer to below table, to control the projector and then press "Enter" key for termination. For example, type "C00" which is a command to turn on the projec- tor, and press "Enter" key. Confirm the projector is turning on.

*Enter with ASCII 64-byte capital characters and one-byte characters.

To disconnect the communication, press "Ctrl" key and "]" key at the same time, type "close" and then press "Enter" key on the Keyboard.

> close [return]

The table below shows the typical command lists for controlling this projector and please consult your local dealer for further information of another commands.

Command list table

Command		Function
	C00	Power on
	C02	Power off
	C09	Volume up
	C0A	Volume down
	C0B	Audio Mute on
	C0C	Audio Mute off
	C1C	Menu display on
	C1D	Menu display off

*1 Further instructions about the telnet application, please see the on-line guide on your computer. *2 The password is a Network PIN code decided item "Network PIN code setting" (☞pp.14, 23). If the authentication of the entered password is failed 4 times continuously, the communication will be

disconnected automatically. Please try again for the connection.

✐If the password or any command is not entered for more than 30 seconds, the communication will be disconnected automatically. Please try again for the connection.

ENGLISH

49

Image 49

Contents Network Set-up and Operation Wired Setting Projector Set-up and OperationFederal Communications Commission Notice ComplianceAddress Telephone No 818998-7322Safety instructions Table of contents Chapter Web Management function +p.31 FeaturesRequired operating environment for computers Network specifications of the projectorUse of this manual Expression/AbbreviationTrademarks Connect the LAN and set the configuration Flow of installationNetwork Configuration has completed Preparation Setup Procedures Connecting to the LAN line Description Network PIN code Numerical value is a setting exampleNetwork factory default Wired LAN factory default settings Chapter Basic Setting and Operation Login Login the setting page of the projectorEnter the IP address Main setting page in the display Display of main settingSub menu tab Switches the sub menu tab Main menu SettingExample of the setting How to use the settingSelect items by ticking on check boxes Select an item by selecting a radio buttonInitial setting PJLink and password setting Network PIN code settingTo 32 alphanumeric characters can be used for the password Whats PJLink?Displays the selected LAN mode Network configurationSets Dhcp configuration ON/OFF Enter e-mail address of administrator Mail settingEnter Smtp password. up to 63 characters Enter Port number of the Smtp server. from 1 toSetting Smtp authentication Setting Smtp server and administrator addressRegistering and deleting E-mail addresses Error message for sending alert mail Setting POP serverExamples Type and contents of alert mail Enter community name to send Trap. Default name is public Snmp settingPJ information Enter user name of the projector etc. optionalTrap check/delete Up to 99,999 hours can be set for the time settingClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector Service in need Power control and status checkDisplays the status of the projectors power. Refer to next Popup confirmation windowStatus Description About projector conditionInput ControlInput signal are listed Input signal are listedSystem Auto is fixed at the Scart inputSuppresses the sound. ON, OFF SoundImage adjustment PC adjustment Screen setting Setting up the projectorSee the next page for the description of other functions Setting Sets into the selected power manage Power OutMent mode Ready, Shutdown, OFF if Input signal is interrupted and noItems Description InformationStatus Indication of the lamp statusControlling the Projector Chapter Appendix Peer-To-Peer connection Examples of connection To another network Entrance hall Gateway Router installed in the networkControl Use of telnetUse the IP address assigned to the projector Command Function Active Script/JavaScript enable Web browser settingProxy setting Windows XP Professional Examples OS/BrowsersInternet Explorer Proxy setting Netscape Navigator JavaScript SettingSafari MAC OS X vHow can I restrict access from the computer Why doesn’t the setting page appear in my web browser?How can I install several projectors? Why am I not receiving E-mail alert messages? Why cant be turned on/off with web browser?Ting What are the rules for IP address assignment? What is the MAC address assigned to the projector?Can I update the firmware of the projector SO-KV8AC