Sanyo PDG-DXL2000 owner manual Compliance, Federal Communications Commission Notice, Address

Page 2

Compliance

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu- nications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise speci- fied in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Numbers	: PDG-DXL2000
Trade Name	: Sanyo
Responsible party	: SANYO NORTH AMERICA CORPORATION
Address	: 21605 Plummer Street, Chatsworth, California 91311
Telephone No.	: (818)998-7322

Image 2

Contents Wired Setting Projector Set-up and Operation Network Set-up and OperationAddress ComplianceFederal Communications Commission Notice Telephone No 818998-7322Safety instructions Table of contents Chapter Features Web Management function +p.31Network specifications of the projector Required operating environment for computersTrademarks Expression/AbbreviationUse of this manual Network Configuration has completed Flow of installationConnect the LAN and set the configuration Preparation Setup Procedures Connecting to the LAN line Description Numerical value is a setting example Network PIN codeNetwork factory default Wired LAN factory default settings Chapter Basic Setting and Operation Enter the IP address Login the setting page of the projectorLogin Sub menu tab Switches the sub menu tab Main menu Display of main settingMain setting page in the display SettingHow to use the setting Example of the settingSelect an item by selecting a radio button Select items by ticking on check boxesInitial setting To 32 alphanumeric characters can be used for the password Network PIN code settingPJLink and password setting Whats PJLink?Sets Dhcp configuration ON/OFF Network configurationDisplays the selected LAN mode Enter Smtp password. up to 63 characters Mail settingEnter e-mail address of administrator Enter Port number of the Smtp server. from 1 toRegistering and deleting E-mail addresses Setting Smtp server and administrator addressSetting Smtp authentication Setting POP server Error message for sending alert mailExamples Type and contents of alert mail PJ information Snmp settingEnter community name to send Trap. Default name is public Enter user name of the projector etc. optionalClick Set button if you tick or un-tick the check box on a Up to 99,999 hours can be set for the time settingTrap check/delete Chapter Controlling the Projector Displays the status of the projectors power. Refer to next Power control and status checkService in need Popup confirmation windowAbout projector condition Status DescriptionControl InputSystem Input signal are listedInput signal are listed Auto is fixed at the Scart inputSound Suppresses the sound. ON, OFFImage adjustment PC adjustment See the next page for the description of other functions Setting up the projectorScreen setting Setting Ment mode Ready, Shutdown, OFF if Power OutSets into the selected power manage Input signal is interrupted and noInformation Items DescriptionIndication of the lamp status StatusControlling the Projector Chapter Appendix To another network Examples of connectionPeer-To-Peer connection Gateway Router installed in the network Entrance hallUse the IP address assigned to the projector Use of telnetControl Command Function Proxy setting Web browser settingActive Script/JavaScript enable Internet Explorer Examples OS/BrowsersWindows XP Professional Proxy setting JavaScript Setting Netscape NavigatorMAC OS X v SafariWhy doesn’t the setting page appear in my web browser? How can I restrict access from the computerHow can I install several projectors? Ting Why cant be turned on/off with web browser?Why am I not receiving E-mail alert messages? What is the MAC address assigned to the projector? What are the rules for IP address assignment?Can I update the firmware of the projector SO-KV8AC