Hitachi 55PD5000, CMP5500, 37PD5000 Remote control, Loading Batteries, Handling the Remote Control

Page 11

Remote control

POWER OFF button 13

POWER ON button 13

MUTE button 14

RGB/VIDEO buttons 14

PinP button 34

AUTO button 16

MENU button 16

OK button 16

ID button 16

			VOL
RGB 1	RGB 2	MUTE	VOL
AV1	AV2	AV3	AV4
AUTO	PinP	SIZE	RECALL
MENU
		OK
ID			ID SET

13POWER ON/OFF button

14VOLUME UP/DOWN buttons

15SIZE button

15RECALL button

16RETURN button

16SELECT/ADJUST buttons

16ID SET button

ENGLISH

Loading Batteries

1. Open the battery cover.

•Slide back and remove the battery

cover in the direction of the arrow.

2.Load batteries.

•Load two Size AA batteries included observing the correct polarities.

3.Close the battery cover.

•Replace the battery cover in the direction of the arrow and snap it back into place.

Handling the Remote Control

Use the remote control within about 5 m from front of the unit’s remote-control sensor and within 30 degrees on both sides.

With in 30

With in 30 degrees degrees

About 3m

About 3m

About 5m

CAUTION

•Do not use new and old batteries together. The batteries could explode or leak, resulting in fires, physical injury, or stains.

•When loading batteries, observe their correct polarities as marked on the product. If loaded in the wrong direction, the batteries could explode or leak, resulting in fires, physical injury, or stains.

ATTENTION

•Do not drop or impact the remote control.

•Do not splash the remote control with water or put it on a wet object to avoid possible failures.

•Before leaving the remote control out of use for an extended period of time, remove the batteries from it.

•If the remote control begins to lack responsiveness, replace the batteries.

•Strong light such as direct sunlight impinging on the photoreceptor of the remote control can cause operational failure. Position this unit to avoid direct contact with such light.

9

Image 11

Contents 37PD5200 55PMA500 Remarque English Features Contents About the Symbols Safety InstructionsTo Earth Fuse Blue to Neutral Cord Clamp Be cautious of the power cord connectionBe sure to keep safety ground connection Be careful in handling the battery of the remote controlSafety Instructions Set the sound volume at a suitable level Precautions for the cable connectionPrecaution during transportation Do not physically impact the remote controlMain Unit Component NamesLoading Batteries Remote controlHandling the Remote Control Securing to a wall or pillar Installation InstructionsInstallation Anti-tumble measuresMonitor rear panel Connecting to a PCPage Operating Instructions Turning Power On and OffAudio Mute Operating Instructions Volume AdjustmentInput Switching When a button is pressed, the volume adjustmentReal mode position Size SwitchingInput Signal Screen Display Display area selection diagram RGB inputIndependent Operation of Multiple Monitors ID No Using the Menu Screen On-screen display systemAutomatic Adjustment of Screen Position and the Clock Operating InstructionsPicture Menu Off Low Middle High Off On Timer MenuOff Timer Min 30Min 60Min 120Min 90Min On Timer Audio MenuFunction Menu Movie Setup MenuOff 1280x768 1366x768 Menu Display Registration condition Other FeaturesLanguage Menu Automatic StoreStatus Display Action Other Features Signal CheckPower Save Mode When the RGB, RGB2 input is selectedAbout residual images Image Retention of Plasma DisplayMethods to Reduce the Occurrence of Image Retention About screen defectsCheck to see if the input signal matches the monitor TroubleshootingSymptoms That Seemingly Appear to be Failures Check the way the signal cable is connectedEnglish Example Troubleshooting Actions to Correct Abnormal DisplaysPin Input signal Product SpecificationsSignal Input RGB terminal D-sub 15-pin connectorDVI terminal DVI-D Product Specifications Signal InputRecommended Signal List With Digital RGB signal input RGB1 inputWith Analog RGB signal input RGB2 input Supplement Optional Video Unit Function Connecting to a Video Imaging DeviceAn example of connecting video imaging devices With DVI-STB and RGB component setupAV1 AV2 AV3 RGB2 RGB1 AV4 Display size selection diagramWhen you want to Input signal Display screen RemarksPress Using a wide-screen monitorTime will display 2 pictures Operating Instructions Displaying Multi PicturePictures Split YNR Black Enhancement Auto Colour Film Mode PAL Comb FilterOperating Instructions Picture Menu Yellow Colour ManagementMagenta RedAV2 1st step AV2 2nd step System Colour SystemVideo Input RGB2 2nd step Audio InputScart Output RGB2 1st stepVideo input Not Used Input connector pin specificationsScart connector pin specifications With component inputKHz MHz Product Specifications Recommended Signal ListWith R, G, B Video input AV2 and AV4 input With component input AV1, AV2 and RGB2-component inputRGB / Video buttons Time button Remote control provided for the optional tuner unitOptional Tuner Unit Function Freeze buttonPressing this button. Each time pressed You may recall the picture mode byPicture mode is changed in following Press this button to change input Surround On or Off ModeButtons for Teletext Mode Monitor rear panel Connecting AntennaPrecautions when connecting the antenna Auto Full Zoom 149Zoom C149L TV AV1 AV2 AV3 RGB2 RGB1 AV4Pictures Split 4 pictures 12 pictures Activating the Split mode from the TV screenMulti Picture button Multi Mode button Button Display will go out in approximately 6 seconds TV position Sound modeOff-timer PicturesSplit Strobe Picture FreezingFreeze button Abcde During TV modeAuto Off Operating Instructions Setup MenuDuring Video signal input Stereo sound broadcast Other FunctionsA2 / Nicam / Sound Multiplex Bilingual / Dual sound broadcastExample Mode button Index button TV / Text button Cancel buttonOperating Instructions Other Functions DVD Player SelectionNo picture or sound Snowy picture poor soundMultiple images sound O.K Intermittent interferenceRF input Input terminals Model Serial Number DEALER/STORE Date Purchased Hitachi Atago Building