Hitachi PJ-TX100 user manual Related messages, Internal portion temperature is rising

Page 36

Troubleshooting

Related messages (continued)

Message

Description

 

The horizontal or vertical wavelength of the inputted

SYNC IS OUT OF RANGE

signal is outside of the response parameters of this unit.

ON *** fH *****kHz fV *****Hz

Please confi rm the specs for this unit or the signal source

 

 

specs.

 

The internal portion temperature is rising.

 

Please turn the power OFF, and allow the unit to cool down

 

at least 20 minutes. After having confi rmed the following

CHECK THE AIR FLOW

items, please turn the power ON again.

 

• Is there blockage of the air passage aperture?

 

• Is the air fi lter dirty?

 

• Does the peripheral temperature exceed 35°C?

CLEAN THE AIR FILTER

A note of precaution when cleaning the air filter.

Please immediately turn the power OFF, and clean or

POWER OFF FIRST,

change the air fi lter by referring to the “Air Filter” section of

THEN CLEAN THE AIR

this manual. After you have cleaned or changed the air fi lter,

FILTER.

please be sure to reset the fi lter timer. If the same message

AFTER CLEANING THE AIR

is displayed after the treatment, please clean the transparent

FILTER,

area of fi lter cover and the dust-detecting window, according

RESET THE FILTER TIMER.

to the following.

CAUTION ►The transparent area of filter cover and the dust-detecting window should be cleaned for normal operation of the optical dust detecting system. Please pay attention not to remain fiber or fragment of cloth inside the duct.

1. Turn off the projector, and unplug the power cord.

2. After making sure that the projector has cooled adequately, remove the fi lter cover.

Hold the release buttons of the fi lter cover, while pulling up it.

3. Wipe the transparent area of the fi lter cover by using a swab or a soft cloth.

4. Remove the air fi lter.

Hold the release buttons of the air fi lter, while pulling up it.

5. Wipecloth. the dust-detecting window by using a soft

6. Replace the air fi lter and fi lter cover.

Release buttons

Filter cover

Transparent area

Air fi lter

Release buttons

Dust detecting window

(Rear side)

(Bottom side)

36

Image 36
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents About contents of package Fastening the lens cover Part names ProjectorRemote control Mode buttonSetting up ArrangementAt 169 screen size At 43 screen sizeUsing the lens shift dials Adjusting the projectors elevatorConnecting your devices About Plug-and-Play capabilityRS-232C DVI out Connecting power supply Remote controlPutting batteries Using the Light button Using the remote controlLight Power on/off Turning on the powerTurning off the power Selecting an input signal OperatingSelecting an aspect ratio Adjusting the zoom and focus Using the automatic adjustment featureImproving the contrast ratio Selecting a mode of picture type Adjusting a black imageAdjusting the picture brightness, contrast, color Recalling your adjustmentMultifunctional settings Using the menu functionMenu Easy MenuEasy Menu Picture Menu GammaCustom Color TempPicture Menu SharpnessProgressive MY MemoryCustom Gamma adjustment Phase Image MenuOver Scan PositionAuto Adjust Image MenuInput Menu Color SpaceComponent Video FormatInput Menu InformationSetup Menu Normal WhisperIris Normal Hinvert Vinvert H&VINVERTScreen Menu Menu PositionOSD Bright Start UPHow to register your picture as the MyScreen Screen MenuMessage Option Menu Auto OFFLamp Time Service Factory ResetOption Menu FanspeedMaintenance Lamp Warning High VoltageCase of replacement by yourself LampAir filter To replace the air filterNJ09452 Caring for the cabinet and remote control Inside of the projectorCaring for the lens Troubleshooting Related messagesInternal portion temperature is rising Signal is outside of the response parameters of this unitRelated messages Horizontal or vertical wavelength of the inputtedRegarding the indicator lamps Regarding the indicator lamps Electrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected These has not been properly fixedPhenomena that may easily be mistaken for machine defects Specification RGB input ports Control portControl DVI-D Video input portsPage Contents of package Adjusting the projectors elevator ArrangementConnecting your devices Connecting the power supply Putting batteries into the remote controlPower STANDBY/ONVideo Lamp Lamp replacement Air filter