Hitachi PJ-TX100 user manual Connecting your devices, About Plug-and-Play capability

Page 8

Setting up

Connecting your devices

WARNING ►Incorrect connecting could result in fi re or electrical shock. Whenever attempting to connect other devices to the projector, please thoroughly read the "User's Manual - Safety Guide", this manual and the manual of each device to be connected.

CAUTION ►Turn off all devices prior to connecting them to the projector. Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector.

►Some cables have to be used with core set. A too long cable may cause a certain picture degradation. Use the accessory cable or a designated-type cable for the connection. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector.

►Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector.

Refer to the section “TECHNICAL” of this manual for the pin assignment of connectors and RS-232C communication data.

NOTE • Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer.

Secure the screws on the connectors and tighten.

Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

For some COMPUTER input modes, the optional Mac adapter is necessary.

When the image resolution is changed on a computer, depending on an input, automatic adjust function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or TFT monitors to change the resolution.

About Plug-and-Play capability

Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC 2B. Plug-and-Play can be achieved by connecting this projector to computers that are VESA DDC (display data channel) compatible.

Please take advantage of this function by connecting the accessory RGB cable to the COMPUTER port (DDC 2B compatible) and/or the optional DVI cable to the DVI-D port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor.

8

Image 8
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents About contents of package Fastening the lens cover Part names ProjectorRemote control Mode buttonSetting up ArrangementAt 169 screen size At 43 screen sizeUsing the lens shift dials Adjusting the projectors elevatorConnecting your devices About Plug-and-Play capabilityRS-232C DVI out Putting batteries Connecting power supplyRemote control Light Using the Light buttonUsing the remote control Turning off the power Power on/offTurning on the power Selecting an aspect ratio Selecting an input signalOperating Improving the contrast ratio Adjusting the zoom and focusUsing the automatic adjustment feature Selecting a mode of picture type Adjusting a black imageAdjusting the picture brightness, contrast, color Recalling your adjustmentMultifunctional settings Using the menu functionMenu Easy MenuEasy Menu Picture Menu GammaCustom Color TempPicture Menu SharpnessProgressive MY MemoryCustom Gamma adjustment Phase Image MenuOver Scan PositionAuto Adjust Image MenuInput Menu Color SpaceComponent Video FormatInput Menu InformationSetup Menu Normal WhisperIris Normal Hinvert Vinvert H&VINVERTScreen Menu Menu PositionOSD Bright Start UPMessage How to register your picture as the MyScreenScreen Menu Lamp Time Option MenuAuto OFF Service Factory ResetOption Menu FanspeedMaintenance Lamp Warning High VoltageCase of replacement by yourself LampNJ09452 Air filterTo replace the air filter Caring for the lens Caring for the cabinet and remote controlInside of the projector Troubleshooting Related messagesInternal portion temperature is rising Signal is outside of the response parameters of this unitRelated messages Horizontal or vertical wavelength of the inputtedRegarding the indicator lamps Regarding the indicator lamps Electrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected These has not been properly fixedPhenomena that may easily be mistaken for machine defects Specification RGB input ports Control portControl DVI-D Video input portsPage Contents of package Adjusting the projectors elevator ArrangementConnecting your devices Connecting the power supply Putting batteries into the remote controlVideo PowerSTANDBY/ON Lamp Lamp replacement Air filter