NEC 151944 system manual Mounting of Daia Card, Mounting Location of Daia Card ND-46550 E

Page 31

2.1.2 Mounting of DAIA Card

STEP 1: Set MB switch on the DAIA card to up position.

STEP 2: Mount DAIA card in the AP slots (AP0-AP7) on the Main Site PIM0-PIM5. A maximum of three DAIA cards can be mounted. Figure 3-6shows

the mounting location of the DAIA card.

On the multiple PIM configuration, the DAIA card(s) must be mounted on the first/last PIM due to the number of connectors of a BUS card.

After mounting the card, set MB switch to down position.

ATTENTION

Contents Static Sensitive

Handling Precautions Required

LT00

LT01

LT02

LT03

LT04

LT05

LT06

LT07

LT08

LT09

LT10/AP0

LT11/AP1

LT12/AP2

LT13/AP3

LT14/AP4

LT14/AP5

LT15/AP6

MP/FP/AP7

BUS/AP8

PWR

Main Site

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PIM0-PIM5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*

 

 

 

DAIA CARD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note 1: For mounting the DAIA card on the slot marked * , the CN connector on the DAIA card should be used.

Note 2: When the clock signal is supplied from a master office, Mount DAIA cards (DAIA0, DAIA1) in PIM0 in order to receive the clock signal.

Figure 3-6 Mounting Location of DAIA Card

ND-46550 (E)

CHAPTER 3

Page 23

Revision 2.0

Image 31
Contents NEC America, Inc Liability Disclaimer NEAX2000 IVS Table of Contents List of Figures List of Figures List of Tables This page is for your notes Reference Manuals Outline of this ManualChapter System Outline System DescriptionPIM Configuration PIM ConfigurationPIM 2shows the system configuration System ConfigurationSN1420 PIMAB-A Required EquipmentRequired Equipment SN1308 PIM P-A PIM Q-UARMT PCM-0.3 CA DAIA, 2 Daic System CapacitySystem Capacity DaiaSystem Conditions Time Slot Allocation Time Slot AllocationFor the switch settings This page is for your notes Precaution in Handling InstallationStatic Electricity Guard PBX Start Installation ProcedureSee Section See .2.6 See Section Location of Lamps, Switches, and Connectors see Figure Lamp Indications on PN-DAIA Card Switch Settings on PN-DAIA Card OFF Setting of control signal time slotNeutral grounding on the receiving line is not Mounting Location of Daia Card ND-46550 E Mounting of Daia CardPN-DAIC Card Switch Setting of Daic CardLamp Indications on PN-DAIC Card Switch Settings on PN-DAIC CardDown SW2 Dip SW When mounting this card on remote Mounting Location of Daic Card Main Site Mounting of Daic CardBUS-DAIA Cable Connection ND-46550 E BUS Cable Connection10 DAIA-DAIC Cable Connection 11 DAIA-DAIC Cable Connection ND-46550 Echapter Revision 12 DAIA-DAIC Cable Connection 13 DAIA-DAIC Cable Connection ND-46550 E 14 PN-DAIB Card Lamp Indications on PN-DAIB Card Switch Settings on PN-DAIB Card TS6 OFF TS7 Down 15 Mounting Location of Daib Card ND-46550 E Mounting of Daib Card16 Mounting Location of Daib Card Refer to , Section 18 Mounting Location of Daic Card Remote PIM 19 Mounting Location of Daic Card Remote PIM ND-46550 E 20 DAIB-DAIC Cable Connection LTC1 LTC Connector Accommodation Small PlatformMounting of Line/Trunk Card on Small Platform PIM LTC022 Location of Each LEN Small Platform LTC0 Mounting of Line/Trunk Card on 1000 IVS PIM LTC Connector Accommodation 1000 IVS25 Location of Each LEN 1000 IVS ND-46550 E 26 LTC Connector Pin Arrangement 1000 IVS Mounting of Line/Trunk Card on PIM N UB 64 port PIM 10 LTC Connector AccommodationPIM N-UB LTC1 28 Location of Each LEN PIM NUB LTC0 30shows an outline of a PFT PN-AUCA connection Power Failure Transfer PFT31 MDF Cross Connection for PFT PN-AUCA ND-46550 E 32shows an outline of a PFT PZ-8PFTA connection PFT0 Connector 34 Mounting PZ-8PFTA Card to PIM 35 PFT Connector Pin Assignment ND-46550 E 36 MDF Cross Connection for PFT PZ-8PFTA PFT1 Connector To Station to PN-4LC to C.O. Line to PN-4COT 37 DTI Cable Connection via LTC Connector PIM0 Daia AA0 BA0 AA1 BA1 LTC1 MDF 39 DTI Cable Connection via CN Connector Main Site DTI Connection at Remote Site MP Reset PN-DAIA Daia Remedial Action on Each Lamp StatusDaib PN-DAIB Daib PN-DAIC Daic This page is for your notes