Kodak i800 Series manual January

Page 72

Sensitivity  controls how aggressively the scanner will work to determine if more than one document is fed into the transport. Multi-feeds are triggered by detecting air gaps between documents. This allows multi-feed detection to be used with job sets containing documents with mixed thicknesses. You may set the Multi-Feed Detection to high, medium or low sensitivity. If you disable Sensitivity, no phase or amplitude checking is used.

NOTE: Regardless of the setting, Post-It™ notes will be detected as multi-fed documents.

•High Sensitivity: this is the most aggressive setting. this is a good setting to use if all documents are similar in thickness to 20-lb. Bond paper.

•Medium Sensitivity: this is the default. Use Medium sensitivity if your application has varying document thickness or labels attached to the document. Depending on the label material, most documents with labels should not be detected as a multi-fed document.

•Low Sensitivity: this setting is the least aggressive setting and is less likely to detect labels, poor quality or wrinkled documents as multi-fed documents.

When determining the appropriate setting for your workflow, you should start at the Medium Sensitivity.

Multifeed Stops Scanning  if this option is not selected, the scanner will display and log the condition but continue to operate. If selected, the scanner will display, log the condition and stop the feeder (the scanner will remain enabled). When an overlap or multi-feed is detected, the scanner stops the feeder, clears the transport of all pages and then the documents can be refed.

End Job  if this option is selected, the scanner will display, log the condition and stop the feeder and transport (the scanner will be disabled). Scanning can only be resumed when the scanner is re-enabled from the host.

With all options, the scanner will beep if the alarm tone volume is set higher than 0.

A-61510 January 2005

3-32

Image 72

Contents User’s Guide Page Introduction Kodak i800 Series ScannersJanuary Image outputs FG.jpg front FB.tif front RB.tif rearGrayscale Bi-tonal/binary Best Practices Basic image captureScanner setup Enable scanning Initiate pollingFeed documents Disable scanning Error handlingJanuary Controlling image transfer order Bi-tonal only duplex Color only duplexJanuary January January January Image file storage locations Bar code recognition Image addressing Image address formatStarting image address Next image addressIndexing schemes Single level indexingTwo level indexing Two level offset indexing Three level indexing January Three level offset indexing Controlling document level changes Generated Automatically Level rules Controlling print strings Electronic color dropout Print String formattingResolution = 200 dpi Contrast% = Threshold = Color Filter =Red dropout Red Dropout  Complete DropoutRed Dropout  Near Complete Dropout Green Dropout  Complete DropoutGreen Dropout  Near Complete Dropout Blue Dropout  Complete DropoutBlue Dropout  Near Complete Dropout Image header information January January Zone processing Original Bi-tonal image Relative CroppingJanuary Programmable keys Patch Reading Types of Patch CodesType 3 Patch Code Type 2 Patch CodeTransfer Patch Code Toggle PatchAdditional Patch Codes Batching Using the Twain Data Source January Scan Validation Tool dialog box Button DescriptionKodak Scanner Properties dialog box Buttons on the Kodak Scanner Properties dialog box Imaging tab January Disabled No Noise Filter Used Contrast Dpi 80 Threshold 20 Contrast Dpi 80 Threshold 100 Contrast Black on White polarity Color January Color Paper tab Cropping values Relative to Document zone processing used for batchesOriginal Bi-tonal image Relative Cropping Overscan values Compression tab Compression tab allows you to compress image filesGood, Better, Best, Superior Dropout tab Green, Remove Blue, Remove RedJanuary January Image Address area Image Address TemplateArea Level to Follow Level Rules Batch tab Batch Control areaPatch Control area PatchPatch 3 assigns a Level 3 to the current document Button Control area Multifeed tab January Options tab January Print Template setup Printer tabPrint String Following information can be printedJanuary Printing orientation Horizontal Print Position Setup tab Info tab Using the Isis Driver January Scan Validation Tool dialog box Opens the image viewer to display one image at a Scanner Settings dialog box Buttons on the Scanner Settings dialog box Enabled and Selected CopyCamera settings area Image Processing settings BinarySize and layout OnlyFixed thresholding ATP disabled January Original Binary image Relative Cropping Automatic  not available for i800 Series Scanners Dpi 80 Threshold 20 Contrast Dpi 80 Threshold 100 Contrast More Scanner Settings dialog box Camera settings area Good, Better, Best, Superior and Sharpen Image Control optionsBlack on White polarity Noise Filter Buttons on the Scanner Settings dialog box Setting scanner ControlsJanuary January January Enabling and setting Document Printer options Print String Formatting characters Counter Text Options − Direction Up or Down Setting Color Dropout values January Defining Batch Patch Code Definition ValuesBatching is the operation of counting pages or documents Enabling Patch Codes Codes boxPatch Image addressing provides better document management Image Address fields January Defining the Scan Area January Appendix a High Volume Scanner Comparison Table Eastman Kodak Company

Related manuals

Manual 83 pages 52.33 Kb