Kodak DP2000 manual Using the Projector, Basic Image Adjustment

Page 25

Using the Projector

This section describes how to use and make adjustments to the projector. It also provides a reference to the keypad and remote control buttons and the options available from the on-screen menus.

Basic Image Adjustment

1.Make sure you have turned on your equipment in the right order (page 17).

2.If the image doesn’t display completely, zoom the image (page 20), adjust the height of the projector (page 20) or center the image by adjusting its horizontal or vertical position (page 29). Be sure the projector is at a 90 degree angle to the screen.

3.If the image is out of focus, rotate the focus lens (page 20).

4.If the image appears to shimmer or if it has blurry vertical bars after you have adjusted the focus, turn Auto Image (page 28) off and then back on to reset the automatic sync and tracking. If that doesn’t clear up the image, turn Auto Image off and adjust the sync (page 29) and/or the tracking (page 29) manually.

5.If the colors don’t look right, check the KODAK Image Manager settings. See “Kodak Menu” on page 35

Or

Adjust the brightness (page 26) and the tint (page 27).

19

Image 25

Contents User’s Guide KODAK DP2000 Digital Projector with KODAK Image Manager SoftwarePage FCC Warning Safety CertificationsCanada EN 55022 WarningPage Safety Instructions Table of ContentsSetting up the Projector Using the ProjectorAppendix B Appendix AAppendix C Appendix DSafety Definitions Safety InstructionsSafety Symbols Important Operating Considerations Safety TermsBattery Use Page Introduction Image ResolutionCompatibility User’s Guide , Quick Start Guide Unpacking the Projectorand Online User Guide CD Usage Guidelines Projector FeaturesIf You Need Assistance Online ServicesFaxed Information Customer Support Warranty Positioning the Projector Setting up the ProjectorConnecting to a Computer Connecting the ProjectorDo you want to play your computer’s audio on the projector? To connect to a computerIf your computer has a PS/2 connector, use the PS/2 mouse cable To connect to a video player Connecting to a Video Player4. Plug the other end of the audio adapter into the audio cable Starting the Projector Turning Off the Projector Basic Image Adjustment Using the ProjectorAdjusting the Projector Using the Projector The Remote Controldisk mouse simulates the right mouse button simulates the left mouse buttonPress anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button the button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Control” starting on page 23 for a description of the four function buttons The Remote Control Buttons Using the Keypad and Remote ControlThe Keypad Buttons Lamp on/off keypad only Volume keypad onlyMenu or Computer and VideoKHQWKHPHQXRSWLRQLVDFWLYH XVHWKHVHEXWWRQVWRQDYLJDWH WKURXJKWKHPHQXV Using the On-Screen MenusBrightness Display MenuContrast Reset All Audio MenuVolume TintAuto Image Image MenuAuto Resize Manual Tracking Manual SyncHorizontal position Vertical position Controls MenuVideo Standard Standby Time Default SourceRear Projection Auto Source SelectDisplay Messages Plug and PlayDisplay Startup Screen Status Menu Language MenuLamp hours used Computer resolutionHorizontal refresh rate Vertical refresh rateImage Manager Settings Kodak MenuThe new contrast setting is immediately applied to the image Using the Image Manager1. Click the Kodak menu Cleaning the Lens Maintenance TroubleshootingSURMHFWRUWRRYHUKHDW Replacing the Projection LampMaintenance & Troubleshooting Be careful when removing the lamp module so that it does not break5. Loosen the two non-removable screws on the outside of the module 6. Grasp the pull tab and lift out the lamp module3OXJLQWKHSRZHUFRUGWRWXUQWKHSURMHFWRUEDFNRQ 9. Tighten the screws on the outside of the module5HSODFHWKHODPSGRRUE\LQVHUWLQJWKHKRRNVRQWKHUHDURIWKH 7RUHVHWWKHODPSKRXUFRXQWHULQWKH6WDWXVZLQGRZSUHVVDQGUsing the Kensington Lock Replacing the Batteries in the Remote ControlProblem Nothing on projection screen TroubleshootingProblem Color or text not being projected Problem The screen resolution is not rightProblem Image is too wide or narrow for screen Problem Only the start-up screen displaysProblem Image is out of focus Problem the projector displays vertical lines, “bleeding” or spots Problem Image and menus are reversed left to rightProblem no sound Problem Image is “noisy” or streakedProblem Lamp shuts off Problem Lamp seems to be getting dimmerPage Dimensions SpecificationsWeight Appendix AOptics Input Power RequirementsLamp Audio InputKey command Portable and Laptop Activation ChartAppendix B ComputerKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activatePage Appendix C Using Video Mirroring with a PowerBook ComputerUsing SimulScan Projected Image Size Appendix DImage Size, Width and Height for DP2000-minimum image size Image Size, Width and Height for DP2000-maximum image sizeIndex L lamp H helpPage Page WARRANTY REPAIR COVERAGE WARRANTY TIME PERIODLIMITATIONS APPLICATION SUPPORTHOW TO OBTAIN SERVICE Page Kodak is a trademark of Eastman Kodak Company Eastman Kodak Company 343 State Street Rochester, New YorkPN 3H7969 9/99