Kodak DP2000 manual Appendix C, Using Video Mirroring with a PowerBook Computer

Page 65

Appendix C

Using Video Mirroring with a PowerBook Computer

When you turn video mirroring (called SimulScan in newer PowerBooks-see below) on, the projector displays the same information that appears on your PowerBook’s built-in screen. When video mirroring is off, the projector acts like a separate display.

To turn on video mirroring for the first time:

1.Open the Monitor’s control panel; click on Monitor 2.

2.Set the number of colors you want.

3.Open the Control Strip; click on the monitor icon.

4.Select “Turn Video Mirroring On.”

Now you can turn video mirroring on and off from the Control Strip without having to open the Monitor’s control panel again.

When using video mirroring and high color graphics such as slide shows, the projected image occasionally might turn black and white. If this happens, perform the following steps:

1.Turn off video mirroring.

2.Open the Monitor’s control panel.

3.Move the white menu bar to Monitor 2 to set the projector as the primary monitor.

4.Restart the PowerBook.

59

Image 65

Contents User’s Guide KODAK DP2000 Digital Projector with KODAK Image Manager SoftwarePage FCC Warning Safety CertificationsCanada EN 55022 WarningPage Safety Instructions Table of ContentsSetting up the Projector Using the ProjectorAppendix B Appendix AAppendix C Appendix DSafety Symbols Safety InstructionsSafety Definitions Important Operating Considerations Safety TermsBattery Use Page Compatibility Image ResolutionIntroduction and Online User Guide CD Unpacking the ProjectorUser’s Guide , Quick Start Guide Usage Guidelines Projector FeaturesFaxed Information Online ServicesIf You Need Assistance Customer Support Warranty Positioning the Projector Setting up the ProjectorConnecting to a Computer Connecting the ProjectorDo you want to play your computer’s audio on the projector? To connect to a computerIf your computer has a PS/2 connector, use the PS/2 mouse cable To connect to a video player Connecting to a Video Player4. Plug the other end of the audio adapter into the audio cable Starting the Projector Turning Off the Projector Basic Image Adjustment Using the ProjectorAdjusting the Projector Using the Projector The Remote Controldisk mouse simulates the right mouse button simulates the left mouse buttonPress anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button the button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Control” starting on page 23 for a description of the four function buttons The Keypad Buttons Using the Keypad and Remote ControlThe Remote Control Buttons Lamp on/off keypad only Volume keypad onlyMenu or Computer and VideoKHQWKHPHQXRSWLRQLVDFWLYH XVHWKHVHEXWWRQVWRQDYLJDWH WKURXJKWKHPHQXV Using the On-Screen MenusContrast Display MenuBrightness Reset All Audio MenuVolume TintAuto Resize Image MenuAuto Image Horizontal position Manual SyncManual Tracking Video Standard Controls MenuVertical position Standby Time Default SourceRear Projection Auto Source SelectDisplay Startup Screen Plug and PlayDisplay Messages Status Menu Language MenuLamp hours used Computer resolutionHorizontal refresh rate Vertical refresh rateImage Manager Settings Kodak Menu1. Click the Kodak menu Using the Image ManagerThe new contrast setting is immediately applied to the image Cleaning the Lens Maintenance TroubleshootingSURMHFWRUWRRYHUKHDW Replacing the Projection LampMaintenance & Troubleshooting Be careful when removing the lamp module so that it does not break5. Loosen the two non-removable screws on the outside of the module 6. Grasp the pull tab and lift out the lamp module3OXJLQWKHSRZHUFRUGWRWXUQWKHSURMHFWRUEDFNRQ 9. Tighten the screws on the outside of the module5HSODFHWKHODPSGRRUE\LQVHUWLQJWKHKRRNVRQWKHUHDURIWKH 7RUHVHWWKHODPSKRXUFRXQWHULQWKH6WDWXVZLQGRZSUHVVDQGUsing the Kensington Lock Replacing the Batteries in the Remote ControlProblem Nothing on projection screen TroubleshootingProblem Color or text not being projected Problem The screen resolution is not rightProblem Image is out of focus Problem Only the start-up screen displaysProblem Image is too wide or narrow for screen Problem the projector displays vertical lines, “bleeding” or spots Problem Image and menus are reversed left to rightProblem no sound Problem Image is “noisy” or streakedProblem Lamp shuts off Problem Lamp seems to be getting dimmerPage Dimensions SpecificationsWeight Appendix AOptics Input Power RequirementsLamp Audio InputKey command Portable and Laptop Activation ChartAppendix B ComputerKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activatePage Appendix C Using Video Mirroring with a PowerBook ComputerUsing SimulScan Projected Image Size Appendix DImage Size, Width and Height for DP2000-minimum image size Image Size, Width and Height for DP2000-maximum image sizeIndex L lamp H helpPage Page WARRANTY REPAIR COVERAGE WARRANTY TIME PERIODLIMITATIONS APPLICATION SUPPORTHOW TO OBTAIN SERVICE Page Kodak is a trademark of Eastman Kodak Company Eastman Kodak Company 343 State Street Rochester, New YorkPN 3H7969 9/99