Kodak DP2000 manual Troubleshooting, Problem Nothing on projection screen

Page 48

Troubleshooting

User’s Guide KODAK DP2000 Digital Projector

Troubleshooting

Problem: Nothing on projection screen

•Make sure that the power cord is properly connected to a fully functional AC electrical outlet. Make sure that the power cord is also properly connected to the projector.

•If the projector is plugged into a power strip, make sure the power strip is turned on.

•Make sure you have removed the lens cap on the projection lens at the front of the projector.

•Make sure the lamp is switched on.

•Check the projector’s lamp to ensure that it is securely connected in the lamp module. See “Replacing the Projection Lamp” on page 38.

•Make sure that the cables do not have any bent pins.

Problem: Color or text not being projected

•You might need to adjust the brightness up or down until the text is visible. Refer to “Brightness” on page 26 for more information.

Problem: The screen resolution is not right

•Make sure the computer’s video card is set for a resolution of no greater than 1024 x 768.

Problem: Image isn’t centered on the screen

•Move the projector to reposition the image.

•Reposition the image using the software. Refer to “Horizontal position” on page 29 and “Vertical position” on page 30.

•Be sure the projector is at a 90 degree angle to the screen.

42

Image 48

Contents with KODAK Image Manager Software User’s Guide KODAK DP2000 Digital ProjectorPage Safety Certifications FCC WarningCanada EN 55022 WarningPage Table of Contents Safety InstructionsSetting up the Projector Using the ProjectorAppendix A Appendix BAppendix C Appendix DSafety Instructions Safety DefinitionsSafety Symbols Safety Terms Important Operating ConsiderationsBattery Use Page Image Resolution IntroductionCompatibility Unpacking the Projector User’s Guide , Quick Start Guideand Online User Guide CD Projector Features Usage GuidelinesOnline Services If You Need AssistanceFaxed Information Customer Support Warranty Setting up the Projector Positioning the ProjectorConnecting the Projector Connecting to a ComputerTo connect to a computer Do you want to play your computer’s audio on the projector?If your computer has a PS/2 connector, use the PS/2 mouse cable Connecting to a Video Player To connect to a video player4. Plug the other end of the audio adapter into the audio cable Starting the Projector Turning Off the Projector Using the Projector Basic Image AdjustmentAdjusting the Projector The Remote Control Using the Projectordisk mouse simulates the right mouse button simulates the left mouse buttonPress anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button the button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Control” starting on page 23 for a description of the four function buttons Using the Keypad and Remote Control The Remote Control ButtonsThe Keypad Buttons Volume keypad only Lamp on/off keypad onlyMenu or Computer and VideoUsing the On-Screen Menus KHQWKHPHQXRSWLRQLVDFWLYH XVHWKHVHEXWWRQVWRQDYLJDWH WKURXJKWKHPHQXVDisplay Menu BrightnessContrast Audio Menu Reset AllVolume TintImage Menu Auto ImageAuto Resize Manual Sync Manual TrackingHorizontal position Controls Menu Vertical positionVideo Standard Default Source Standby TimeRear Projection Auto Source SelectPlug and Play Display MessagesDisplay Startup Screen Language Menu Status MenuComputer resolution Lamp hours usedHorizontal refresh rate Vertical refresh rateKodak Menu Image Manager SettingsUsing the Image Manager The new contrast setting is immediately applied to the image1. Click the Kodak menu Maintenance Troubleshooting Cleaning the LensReplacing the Projection Lamp SURMHFWRUWRRYHUKHDWBe careful when removing the lamp module so that it does not break Maintenance & Troubleshooting5. Loosen the two non-removable screws on the outside of the module 6. Grasp the pull tab and lift out the lamp module9. Tighten the screws on the outside of the module 3OXJLQWKHSRZHUFRUGWRWXUQWKHSURMHFWRUEDFNRQ5HSODFHWKHODPSGRRUE\LQVHUWLQJWKHKRRNVRQWKHUHDURIWKH 7RUHVHWWKHODPSKRXUFRXQWHULQWKH6WDWXVZLQGRZSUHVVDQGReplacing the Batteries in the Remote Control Using the Kensington LockTroubleshooting Problem Nothing on projection screenProblem Color or text not being projected Problem The screen resolution is not rightProblem Only the start-up screen displays Problem Image is too wide or narrow for screenProblem Image is out of focus Problem Image and menus are reversed left to right Problem the projector displays vertical lines, “bleeding” or spotsProblem no sound Problem Image is “noisy” or streakedProblem Lamp seems to be getting dimmer Problem Lamp shuts offPage Specifications DimensionsWeight Appendix AInput Power Requirements OpticsLamp Audio InputPortable and Laptop Activation Chart Key commandAppendix B ComputerKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activatePage Using Video Mirroring with a PowerBook Computer Appendix CUsing SimulScan Appendix D Projected Image SizeImage Size, Width and Height for DP2000-maximum image size Image Size, Width and Height for DP2000-minimum image sizeIndex H help L lampPage Page WARRANTY TIME PERIOD WARRANTY REPAIR COVERAGELIMITATIONS APPLICATION SUPPORTHOW TO OBTAIN SERVICE Page Eastman Kodak Company 343 State Street Rochester, New York Kodak is a trademark of Eastman Kodak CompanyPN 3H7969 9/99