Kodak DP2000 manual Important Operating Considerations, Safety Terms

Page 8
Safety Terms

User’s Guide KODAK DP2000 Digital Projector

Safety Terms

Warning: Don’t look directly into the lens when the projector is turned on.

Warning: To replace the lamp, turn the power off and unplug the power cord. To avoid burns, wait 30 minutes before opening the lamp door. Follow all instructions pro- vided in this User’s Guide.

Warning: Please use the power cord provided. Connect the power cord to a receptacle with a protective safety (earth) ground terminal.

Warning: Refer all service to qualified service personnel. Servic- ing your own projector will void the warranty. See “If You Need Assistance” on page 8 for the customer service contact informa- tion.

Caution: Don’t block ventilation openings.

Caution: Don’t set liquids on the projector. Spilled liquids may damage your projector.

Caution: Don’t place the projector on a hot surface or in direct sunlight.

Caution: Do not drop the projector. Transport the projector in a Kodak-approved case.

Important Operating Considerations

Do not place the projector on a tablecloth or other soft covering that may block the vents. In the unlikely event of the bulb rupturing, thoroughly clean the area behind the projector and discard any edible items placed in that area.

 

 

6m)

 

 

.

 

(

t

 

f

 

 

2

 

 

Do not place objects in

this area behind the projector

2

Image 8
Contents with KODAK Image Manager Software User’s Guide KODAK DP2000 Digital ProjectorPage Safety Certifications FCC WarningCanada EN 55022 WarningPage Table of Contents Safety InstructionsSetting up the Projector Using the ProjectorAppendix A Appendix BAppendix C Appendix DSafety Symbols Safety InstructionsSafety Definitions Safety Terms Important Operating ConsiderationsBattery Use Page Compatibility Image ResolutionIntroduction and Online User Guide CD Unpacking the ProjectorUser’s Guide , Quick Start Guide Projector Features Usage GuidelinesFaxed Information Online ServicesIf You Need Assistance Customer Support Warranty Setting up the Projector Positioning the ProjectorConnecting the Projector Connecting to a ComputerTo connect to a computer Do you want to play your computer’s audio on the projector?If your computer has a PS/2 connector, use the PS/2 mouse cable Connecting to a Video Player To connect to a video player4. Plug the other end of the audio adapter into the audio cable Starting the Projector Turning Off the Projector Using the Projector Basic Image AdjustmentAdjusting the Projector The Remote Control Using the Projectordisk mouse simulates the right mouse button simulates the left mouse buttonPress anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button the button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Control” starting on page 23 for a description of the four function buttons The Keypad Buttons Using the Keypad and Remote ControlThe Remote Control Buttons Volume keypad only Lamp on/off keypad onlyMenu or Computer and VideoUsing the On-Screen Menus KHQWKHPHQXRSWLRQLVDFWLYH XVHWKHVHEXWWRQVWRQDYLJDWH WKURXJKWKHPHQXVContrast Display MenuBrightness Audio Menu Reset AllVolume TintAuto Resize Image MenuAuto Image Horizontal position Manual SyncManual Tracking Video Standard Controls MenuVertical position Default Source Standby TimeRear Projection Auto Source SelectDisplay Startup Screen Plug and PlayDisplay Messages Language Menu Status MenuComputer resolution Lamp hours usedHorizontal refresh rate Vertical refresh rateKodak Menu Image Manager Settings1. Click the Kodak menu Using the Image ManagerThe new contrast setting is immediately applied to the image Maintenance Troubleshooting Cleaning the LensReplacing the Projection Lamp SURMHFWRUWRRYHUKHDWBe careful when removing the lamp module so that it does not break Maintenance & Troubleshooting5. Loosen the two non-removable screws on the outside of the module 6. Grasp the pull tab and lift out the lamp module9. Tighten the screws on the outside of the module 3OXJLQWKHSRZHUFRUGWRWXUQWKHSURMHFWRUEDFNRQ5HSODFHWKHODPSGRRUE\LQVHUWLQJWKHKRRNVRQWKHUHDURIWKH 7RUHVHWWKHODPSKRXUFRXQWHULQWKH6WDWXVZLQGRZSUHVVDQGReplacing the Batteries in the Remote Control Using the Kensington LockTroubleshooting Problem Nothing on projection screenProblem Color or text not being projected Problem The screen resolution is not rightProblem Image is out of focus Problem Only the start-up screen displaysProblem Image is too wide or narrow for screen Problem Image and menus are reversed left to right Problem the projector displays vertical lines, “bleeding” or spotsProblem no sound Problem Image is “noisy” or streakedProblem Lamp seems to be getting dimmer Problem Lamp shuts offPage Specifications DimensionsWeight Appendix AInput Power Requirements OpticsLamp Audio InputPortable and Laptop Activation Chart Key commandAppendix B ComputerKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activatePage Using Video Mirroring with a PowerBook Computer Appendix CUsing SimulScan Appendix D Projected Image SizeImage Size, Width and Height for DP2000-maximum image size Image Size, Width and Height for DP2000-minimum image sizeIndex H help L lampPage Page WARRANTY TIME PERIOD WARRANTY REPAIR COVERAGELIMITATIONS APPLICATION SUPPORTHOW TO OBTAIN SERVICE Page Eastman Kodak Company 343 State Street Rochester, New York Kodak is a trademark of Eastman Kodak CompanyPN 3H7969 9/99