Kodak DP2000 manual Safety Instructions, Safety Definitions, Safety Symbols

Page 7

Safety Instructions

Safety Instructions

Please read and follow all safety instructions provided before using your new projector. Failure to comply with safety instructions may result in fire, electrical shock, or personal injury and may damage or impair protection provided by equipment. Please save all safety instructions.

Safety Definitions

•Warning: Statements identify conditions or practices that could result in permanent personal injury.

•Caution: Statements identify conditions or practices that could result in damage to your equipment.

Safety Symbols

Attention: For information about use of a feature, please refer to this User’s Guide.

Warning: Hot surface. Do not touch.

An arrow pointing to the lamp door on the projector.

1

Image 7

Contents User’s Guide KODAK DP2000 Digital Projector with KODAK Image Manager SoftwarePage EN 55022 Warning Safety CertificationsFCC Warning CanadaPage Using the Projector Table of ContentsSafety Instructions Setting up the ProjectorAppendix D Appendix AAppendix B Appendix CSafety Definitions Safety InstructionsSafety Symbols Important Operating Considerations Safety TermsBattery Use Page Introduction Image ResolutionCompatibility User’s Guide , Quick Start Guide Unpacking the Projectorand Online User Guide CD Usage Guidelines Projector FeaturesIf You Need Assistance Online ServicesFaxed Information Customer Support Warranty Positioning the Projector Setting up the ProjectorConnecting to a Computer Connecting the ProjectorDo you want to play your computer’s audio on the projector? To connect to a computerIf your computer has a PS/2 connector, use the PS/2 mouse cable To connect to a video player Connecting to a Video Player4. Plug the other end of the audio adapter into the audio cable Starting the Projector Turning Off the Projector Basic Image Adjustment Using the ProjectorAdjusting the Projector simulates the left mouse button The Remote ControlUsing the Projector disk mouse simulates the right mouse buttonPress anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button the button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Control” starting on page 23 for a description of the four function buttons The Remote Control Buttons Using the Keypad and Remote ControlThe Keypad Buttons or Computer and Video Volume keypad onlyLamp on/off keypad only MenuKHQWKHPHQXRSWLRQLVDFWLYH XVHWKHVHEXWWRQVWRQDYLJDWH WKURXJKWKHPHQXV Using the On-Screen MenusBrightness Display MenuContrast Tint Audio MenuReset All VolumeAuto Image Image MenuAuto Resize Manual Tracking Manual SyncHorizontal position Vertical position Controls MenuVideo Standard Auto Source Select Default SourceStandby Time Rear ProjectionDisplay Messages Plug and PlayDisplay Startup Screen Status Menu Language MenuVertical refresh rate Computer resolutionLamp hours used Horizontal refresh rateImage Manager Settings Kodak MenuThe new contrast setting is immediately applied to the image Using the Image Manager1. Click the Kodak menu Cleaning the Lens Maintenance TroubleshootingSURMHFWRUWRRYHUKHDW Replacing the Projection Lamp6. Grasp the pull tab and lift out the lamp module Be careful when removing the lamp module so that it does not breakMaintenance & Troubleshooting 5. Loosen the two non-removable screws on the outside of the module7RUHVHWWKHODPSKRXUFRXQWHULQWKH6WDWXVZLQGRZSUHVVDQG 9. Tighten the screws on the outside of the module3OXJLQWKHSRZHUFRUGWRWXUQWKHSURMHFWRUEDFNRQ 5HSODFHWKHODPSGRRUE\LQVHUWLQJWKHKRRNVRQWKHUHDURIWKHUsing the Kensington Lock Replacing the Batteries in the Remote ControlProblem The screen resolution is not right TroubleshootingProblem Nothing on projection screen Problem Color or text not being projectedProblem Image is too wide or narrow for screen Problem Only the start-up screen displaysProblem Image is out of focus Problem Image is “noisy” or streaked Problem Image and menus are reversed left to rightProblem the projector displays vertical lines, “bleeding” or spots Problem no soundProblem Lamp shuts off Problem Lamp seems to be getting dimmerPage Appendix A SpecificationsDimensions WeightAudio Input Input Power RequirementsOptics LampComputer Portable and Laptop Activation ChartKey command Appendix Bde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command ComputerPage Appendix C Using Video Mirroring with a PowerBook ComputerUsing SimulScan Projected Image Size Appendix DImage Size, Width and Height for DP2000-minimum image size Image Size, Width and Height for DP2000-maximum image sizeIndex L lamp H helpPage Page APPLICATION SUPPORT WARRANTY TIME PERIODWARRANTY REPAIR COVERAGE LIMITATIONSHOW TO OBTAIN SERVICE Page 9/99 Eastman Kodak Company 343 State Street Rochester, New YorkKodak is a trademark of Eastman Kodak Company PN 3H7969