Kodak DP2000 manual Problem Only the start-up screen displays, Problem Image is out of focus

Page 49

Problem: Only the start-up screen displays

Maintenance & Troubleshooting

Problem: Only the start-up screen displays

•Verify that the cables are connected correctly. See page 12 through page 16 for connection procedures.

•Verify that the proper input source is selected. See “Source (keypad only) or Computer and Video (remote control only)” on page 24.

•You might need to turn everything off and turn on the equipment again in the proper order. Refer to your computer documentation to determine the correct order.

•Make sure your laptop external video port is turned on. See the “Portable and Laptop Activation Chart” on page 49 in this guide or your computer’s manual for details.

•Make sure your computer video board is installed and configured correctly.

•Make sure your computer has a compatible video board. The projector isn’t CGA, EGA or SXGA compatible.

If you’re using Windows 98:

1.Open "My Computer" icon, the Control Panel folder and then the Display icon.

2.Click the Settings tab.

3.Verify that the Desktop area is set to 1024 x 768 or less.

Problem: Image is too wide or narrow for screen

•Adjust the zoom or projector placement.

•Adjust the resolution of your video card if it’s greater than 1024 x 768.

Problem: Image is out of focus

•Turn the projection lens to focus the image.

•Make sure the projection screen is at least 5 feet (1.5 m) from the projector.

•Check the projection lens to see if it needs cleaning.

43

Image 49

Contents User’s Guide KODAK DP2000 Digital Projector with KODAK Image Manager SoftwarePage FCC Warning Safety CertificationsCanada EN 55022 WarningPage Safety Instructions Table of ContentsSetting up the Projector Using the ProjectorAppendix B Appendix AAppendix C Appendix DSafety Definitions Safety InstructionsSafety Symbols Important Operating Considerations Safety TermsBattery Use Page Introduction Image ResolutionCompatibility User’s Guide , Quick Start Guide Unpacking the Projectorand Online User Guide CD Usage Guidelines Projector FeaturesIf You Need Assistance Online ServicesFaxed Information Customer Support Warranty Positioning the Projector Setting up the ProjectorConnecting to a Computer Connecting the ProjectorDo you want to play your computer’s audio on the projector? To connect to a computerIf your computer has a PS/2 connector, use the PS/2 mouse cable To connect to a video player Connecting to a Video Player4. Plug the other end of the audio adapter into the audio cable Starting the Projector Turning Off the Projector Basic Image Adjustment Using the ProjectorAdjusting the Projector Using the Projector The Remote Controldisk mouse simulates the right mouse button simulates the left mouse buttonPress anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button the button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Control” starting on page 23 for a description of the four function buttons The Remote Control Buttons Using the Keypad and Remote ControlThe Keypad Buttons Lamp on/off keypad only Volume keypad onlyMenu or Computer and VideoKHQWKHPHQXRSWLRQLVDFWLYH XVHWKHVHEXWWRQVWRQDYLJDWH WKURXJKWKHPHQXV Using the On-Screen MenusBrightness Display MenuContrast Reset All Audio MenuVolume TintAuto Image Image MenuAuto Resize Manual Tracking Manual SyncHorizontal position Vertical position Controls MenuVideo Standard Standby Time Default SourceRear Projection Auto Source SelectDisplay Messages Plug and PlayDisplay Startup Screen Status Menu Language MenuLamp hours used Computer resolutionHorizontal refresh rate Vertical refresh rateImage Manager Settings Kodak MenuThe new contrast setting is immediately applied to the image Using the Image Manager1. Click the Kodak menu Cleaning the Lens Maintenance TroubleshootingSURMHFWRUWRRYHUKHDW Replacing the Projection LampMaintenance & Troubleshooting Be careful when removing the lamp module so that it does not break5. Loosen the two non-removable screws on the outside of the module 6. Grasp the pull tab and lift out the lamp module3OXJLQWKHSRZHUFRUGWRWXUQWKHSURMHFWRUEDFNRQ 9. Tighten the screws on the outside of the module5HSODFHWKHODPSGRRUE\LQVHUWLQJWKHKRRNVRQWKHUHDURIWKH 7RUHVHWWKHODPSKRXUFRXQWHULQWKH6WDWXVZLQGRZSUHVVDQGUsing the Kensington Lock Replacing the Batteries in the Remote ControlProblem Nothing on projection screen TroubleshootingProblem Color or text not being projected Problem The screen resolution is not rightProblem Image is too wide or narrow for screen Problem Only the start-up screen displaysProblem Image is out of focus Problem the projector displays vertical lines, “bleeding” or spots Problem Image and menus are reversed left to rightProblem no sound Problem Image is “noisy” or streakedProblem Lamp shuts off Problem Lamp seems to be getting dimmerPage Dimensions SpecificationsWeight Appendix AOptics Input Power RequirementsLamp Audio InputKey command Portable and Laptop Activation ChartAppendix B ComputerKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activateKey command Key commandComputer de-activatePage Appendix C Using Video Mirroring with a PowerBook ComputerUsing SimulScan Projected Image Size Appendix DImage Size, Width and Height for DP2000-minimum image size Image Size, Width and Height for DP2000-maximum image sizeIndex L lamp H helpPage Page WARRANTY REPAIR COVERAGE WARRANTY TIME PERIODLIMITATIONS APPLICATION SUPPORTHOW TO OBTAIN SERVICE Page Kodak is a trademark of Eastman Kodak Company Eastman Kodak Company 343 State Street Rochester, New YorkPN 3H7969 9/99