Kodak DP2000 manual Replacing the Batteries in the Remote Control, Using the Kensington Lock

Page 47

Replacing the Batteries in the Remote Control

Maintenance & Troubleshooting

Replacing the Batteries in the Remote Control

The life of the batteries depends on how often and how long you use the remote control. Symptoms of low battery charge include erratic responses when using the remote control and a reduced range of operation.

Follow these steps to replace the batteries:

1.Turn the remote control face down in your hand.

2.Slide the battery cover off the end of the remote control.

3.Remove the old batteries and properly dispose of them.

4.Install two new AAA alkaline batteries. Make sure you install each battery in the correct direction.

5.Slide the battery cover back on the remote control.

Using the Kensington Lock

The projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector.

DLP

Includes

Manager

Image

41

Image 47

Contents User’s Guide KODAK DP2000 Digital Projector with KODAK Image Manager SoftwarePage EN 55022 Warning Safety CertificationsFCC Warning CanadaPage Using the Projector Table of ContentsSafety Instructions Setting up the ProjectorAppendix D Appendix AAppendix B Appendix CSafety Symbols Safety InstructionsSafety Definitions Important Operating Considerations Safety TermsBattery Use Page Compatibility Image ResolutionIntroduction and Online User Guide CD Unpacking the ProjectorUser’s Guide , Quick Start Guide Usage Guidelines Projector FeaturesFaxed Information Online ServicesIf You Need Assistance Customer Support Warranty Positioning the Projector Setting up the ProjectorConnecting to a Computer Connecting the ProjectorDo you want to play your computer’s audio on the projector? To connect to a computerIf your computer has a PS/2 connector, use the PS/2 mouse cable To connect to a video player Connecting to a Video Player4. Plug the other end of the audio adapter into the audio cable Starting the Projector Turning Off the Projector Basic Image Adjustment Using the ProjectorAdjusting the Projector simulates the left mouse button The Remote ControlUsing the Projector disk mouse simulates the right mouse buttonPress anywhere on the edge of the disk mouse to move the cursor on the screen. You can move the cursor at any angle by pressing the corresponding edge of the disk. The mouse button on the top of the remote simulates your computer’s right mouse button the button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Control” starting on page 23 for a description of the four function buttons The Keypad Buttons Using the Keypad and Remote ControlThe Remote Control Buttons or Computer and Video Volume keypad onlyLamp on/off keypad only MenuKHQWKHPHQXRSWLRQLVDFWLYH XVHWKHVHEXWWRQVWRQDYLJDWH WKURXJKWKHPHQXV Using the On-Screen MenusContrast Display MenuBrightness Tint Audio MenuReset All VolumeAuto Resize Image MenuAuto Image Horizontal position Manual SyncManual Tracking Video Standard Controls MenuVertical position Auto Source Select Default SourceStandby Time Rear ProjectionDisplay Startup Screen Plug and PlayDisplay Messages Status Menu Language MenuVertical refresh rate Computer resolutionLamp hours used Horizontal refresh rateImage Manager Settings Kodak Menu1. Click the Kodak menu Using the Image ManagerThe new contrast setting is immediately applied to the image Cleaning the Lens Maintenance TroubleshootingSURMHFWRUWRRYHUKHDW Replacing the Projection Lamp6. Grasp the pull tab and lift out the lamp module Be careful when removing the lamp module so that it does not breakMaintenance & Troubleshooting 5. Loosen the two non-removable screws on the outside of the module7RUHVHWWKHODPSKRXUFRXQWHULQWKH6WDWXVZLQGRZSUHVVDQG 9. Tighten the screws on the outside of the module3OXJLQWKHSRZHUFRUGWRWXUQWKHSURMHFWRUEDFNRQ 5HSODFHWKHODPSGRRUE\LQVHUWLQJWKHKRRNVRQWKHUHDURIWKHUsing the Kensington Lock Replacing the Batteries in the Remote ControlProblem The screen resolution is not right TroubleshootingProblem Nothing on projection screen Problem Color or text not being projectedProblem Image is out of focus Problem Only the start-up screen displaysProblem Image is too wide or narrow for screen Problem Image is “noisy” or streaked Problem Image and menus are reversed left to rightProblem the projector displays vertical lines, “bleeding” or spots Problem no soundProblem Lamp shuts off Problem Lamp seems to be getting dimmerPage Appendix A SpecificationsDimensions WeightAudio Input Input Power RequirementsOptics LampComputer Portable and Laptop Activation ChartKey command Appendix Bde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command Computerde-activate Key commandKey command ComputerPage Appendix C Using Video Mirroring with a PowerBook ComputerUsing SimulScan Projected Image Size Appendix DImage Size, Width and Height for DP2000-minimum image size Image Size, Width and Height for DP2000-maximum image sizeIndex L lamp H helpPage Page APPLICATION SUPPORT WARRANTY TIME PERIODWARRANTY REPAIR COVERAGE LIMITATIONSHOW TO OBTAIN SERVICE Page 9/99 Eastman Kodak Company 343 State Street Rochester, New YorkKodak is a trademark of Eastman Kodak Company PN 3H7969