Kodak 4400, 4200-KK, 5600-KK, 4600-KK, 5600-J, 4200-J service manual Adjusting the Photocell

Page 30

SERVICE MANUAL

Important

If you cannot obtain the NULL position after doing the adjustment approximately 3 times, go to the adjustment procedure for the PHOTOCELL.

	light path
	T-BAR
	TL-3003
	NULL position
PROJECTION	TAB
LENS	TAB

		AUTO-FOCUS	CLAMP LEVER
		TARGET SLIDE
	A091_4031BCA		PAD
	A091_4031BA	TL-3002

Adjustment Speciﬁcation

Use TL-3002 and FAN CAP 232729 to check the adjustment of the PHOTOCELL.

Adjusting the PHOTOCELL

PHOTOCELL

CIRCUIT BOARD

wratten FILTER (2)

Warning

Dangerous Voltage

[1]Disconnect the main power.

[2]Do the removal for the LOWER HOUSING ASSEMBLY.

Important

It is necessary to make a FAN COVER TOOL. See the Tools section.

[3]Install the FAN COVER TOOL over the FAN area and the LAMP MODULE. See the Tools section.

	POST (2)	PHOTOCELL
		MASK

	PHOTOCELL	A091_4032GCA
	HOUSING
		A091_4032GA

30	18NOV97 – SM5440-1

Image 30

Contents Kodak Carousel Projectors Table of Contents Adjusting the Focus Light Path Auto Focus Models Replacing the Lower Housing Assembly Installing the Lower Housing AssemblyReplacing the FAN Shaft Assembly Replacements and Installations Installing the FAN Shaft Assembly FAN BeltInstalling the Motor Replacing the MotorScrew Motor Replacing the Worm Pulley and Mechanism Belt Installing the Worm Pulley and Mechanism Belt Worm Pulley Screw Mechanism BeltReplacing the Thermal Fuse Assembly Installing the Thermal Fuse AssemblyReplacing the Lamp Module Receptacle Installing the Lamp Module Receptacle Plunger Assembly Replacing the Cycle Solenoid AssemblyInstalling the Cycle Solenoid Assembly Pulley ShaftReplacing the Mechanism Assembly Installing the Mechanism AssemblyMechanism Assembly Replacing the CAM Stack Assembly and Cycle Lever Assembly Replacing the AUTO-FOCUS Bracket AssemblyInstalling the AUTO-FOCUS Bracket Assembly Worm Pulley Auto Focusscrew Cyclebracket Solenoid AssemblyLift Lever Shaft Select Lever A0910010HCA Installing the CAM Stack Assembly and Cycle Lever Assembly Replacing the Lamp Socket Terminal Assembly Installing the Lamp Socket Terminal AssemblyLamp Door Replacing the Lens Mount Assembly Auto Focus Model Installing the Lens Mount Assembly Auto Focus ModelsReplacing the Lens Mount Assembly Non Auto Focus Model Installing the Lens Mount Assembly Non Auto Focus ModelReplacing the AUTO-FOCUS Switch Assembly Installing the AUTO-FOCUS Switch AssemblyReplacing the Focus Shaft Assembly Auto Focus Models Assembly Lens Mount AssemblySwitch Clamp Lever ScrewInstalling the Focus Shaft Assembly Replacing the Focus Shaft Assembly Non Auto-Focus ModelsInstalling the Focus Shaft Assembly Adjustment Speciﬁcation Adjusting the Cycle SolenoidMechanism Assembly BAR Adjusting the Indexer Lever Assembly Adjusting the Slide Lift Lever MANUAL, with Mechanism Out Adjusting the Slide Lift Lever Power with Mechanism OutSlide Lift Lever Guage TL-3001 Select Slide Lift Lever Guage TL-3001 Select Spring Hook TL-1165 Auto Focus Bracket Assembly Adjusting the NullAdjustment Tool AUTO-FOCUS Target Slide TL-3002Adjusting the Photocell Soldering Iron Photocell MaskFAN CAP Housing Clamp Lever PADAUTO-FOCUS Assembly Target Slide FAN CAPClamp PAD Adjusting the Clamp PAD Assembly Adjusting the Dark ShutterScrew NUT Clamp PAD Assembly Dark Shutter Pressure PAD Worm Pulley Assembly CAM Stack Assembly Cycle Levers FANLubrication A0910022DA AUTO-FOCUS Target Slide Adjustment T-BARAUTO-FOCUS Gauge Super LubeSpecifications Grounded Power CordsPIN Remote Control Diagnostics Main Motor VoltagesPhotocell Voltages PIN Remote Cord Plug VoltagesSmall Component Board Assembly 256809 Voltages Power, Illumination, and Cooling Malfunctions Voltage Speciﬁcations General PartsSuper Lube TL-4276 Slide Transport MalfunctionsControl Cycle LeverEccentrics Lever AssemblyPower Slide Lift Lever Direction LeverFocus Malfunctions Gate Mechanism BoardCheck that the alignment of the Target Eastman Kodak Company