FARGO electronic Quatro ID Card Printer manual On/cancel LED light is flashing

Page 40

encoded properly or encoded onto a bad magnetic stripe, the printer is unable to verify the encoded data. When this happens, the printer will simply eject the card before printing begins and the on-line LED will begin flashing. Press the on-line button to resume encoding and printing with a new card.

The on/cancel LED light is flashing.

¥If the on/cancel LED is flashing, this indicates a possible error with your printerÕs memory. Contact your authorized reseller for technical assistance.

I’m having problems printing from Windows 95/98.

¥Print with either the 32-Bit Print Spooler or the Write Direct to Port option selected from within the printer driver setup (see Chapter 4, Section IV for more information on these options). In most cases, one or the other of these options will provide the best results when printing from Windows 95/98.

¥Due to the wide variety of PC hardware and software configurations, however, some systems may print more effectively through the Windows 95/98 print spooler. If you choose not to print with either the 32-Bit Print Spooler or the Write Direct to Port option selected, but instead wish to print through the Windows print spooler, the following steps will help you optimize your system for printing:

1.Click the Start button, point to Settings, and select Printers. When the Printers window appears, click on the Quatro printer icon using the right mouse button, and select the Properties option.

2.Select the Details tab, then select the Spool Settings button.

3.Select the Print directly to the printer option and click on OK.

4.Again from the Details tab, select the Port Settings button.

5.Deselect both the Check Port state before printing option and the Spool MS-DOS print jobs option, and click on OK.

6.Increase the Transmission retry value of the Details tab from 45 to 900. Click on OK to close the Properties window.

36 Troubleshooting

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Quatro ID Card Printer UserÕs Manual Printing History Table of Contents Appendix a Magnetic Stripe Encoding Module Getting Started Thank YOUChoosing a Good Location II. about Moisture CondensationIII. Unpacking and Inspection Powering Up the Printer Applying PowerPower Input Port II. Identifying the Printer Features Ribbons and Cards About RibbonsII. Loading Ribbon Into the Printer Release Tab Printhead Assembly Take-up Ribbon Supply Ribbon Drive Hubs Ribbon Sensor III. about Cards IV. Loading Cards Into the PrinterCard Stack Card Input Tray Printing a Self Test Using the Quatro ID Card Printer Connecting the Printer to Your ComputerII. Installing the Windows Printer Driver Windows 95/98 or Windows NTWindows III. Installing the 32-BIT Print Spooler for Windows 95/98 PanelUsing the Quatro ID Card Printer IV. Setting UP the Windows Printer Driver Windows NT Windows 95/98Card Size Color Matching ControlsDither Mode Fast 32-bit SpoolerPanel Graphics Magnetics Mag Encode OnlyNo Margins Position Rear of PrinterRotate Ribbon TypeWrite Direct to Port Printing a Card Maintenance Supplies RequiredII. Standard Printhead Cleaning III. Expanded Printhead Cleaning IV. Cleaning the PRINTER’S CaseCleaning the Inside of the Printer VI. Clearing a Card JAMVIII. Cleaning the Card Feed Rollers VII. Clearing a Ribbon JAMInsert this end first Sticky Side Up IX. Cleaning the Drive Roller Maintaining the Cleaning RollersMaintenance Printer doesn’t work at all TroubleshootingOn-line LED light is flashing On/cancel LED light is flashing ’m having problems printing from Windows 95/98Ribbon doesn’t seem to wind or print properly Card or ribbon is jammed Ribbon has torn or even brokenMy prints have streaks in them My prints have blotches small voids in themPhotos on my ID cards look very pixelated Card won’t feed and the on-line LED starts blinkingPrinting gets cut off or is not centered on the card Two or more cards feed at the same timeTechnical Specifications Printing AreaEncoding Mode / Magnetic Track Selection Magnectic Track OptionsMagnetic Track Options Encoded Bit DensityLRC Generation Mode Character Data SizeCharacter Ascii Offset Character Data ParityII. Track Locations III. Sending Track Information~1%JULIE ANDERSON623-85-1253? Introduction Appendix B Interfacing InformationII. CENTRONICS-TYPE Parallel Interface Index Drive rollerRibbon type Page

Quatro ID Card Printer specifications

The FARGO Electronic Quattro ID Card Printer is a versatile and efficient solution for creating high-quality identification cards. This state-of-the-art printer is designed to cater to a variety of industries, including education, healthcare, and corporate environments, making it an ideal choice for organizations that require reliable and secure ID card printing.

One of the standout features of the Quattro ID Card Printer is its ability to produce vibrant, full-color cards with exceptional clarity. Utilizing advanced dye-sublimation technology, the printer ensures that images and text are reproduced with remarkable precision. The printer has a resolution of 300 dpi, providing sharp details and rich colors that enhance the overall appearance of the ID cards.

Another key characteristic of the Quattro printer is its dual-sided printing capability. This feature allows users to print on both sides of the card in a single pass, significantly reducing production time and enhancing productivity. Organizations can utilize the back side of the card for vital information, such as magnetic stripes, barcodes, or additional identification details.

The Quattro ID Card Printer also incorporates smart card encoding technology, which enables the printing and encoding of RFID and smart chip technology onto cards. This is particularly beneficial for organizations that require heightened security measures, as it allows for the storage of sensitive information directly on the ID card itself.

User-friendliness is another essential aspect of the FARGO Quattro ID Card Printer. The device features an intuitive interface with easy-to-navigate controls, making it accessible for operators of all skill levels. Additionally, the printer is designed for seamless integration with existing software systems, facilitating a smooth workflow.

The robust build and compact design of the Quattro printer make it suitable for a variety of settings. Its durable construction ensures longevity while occupying minimal space on a desk or workstation. Furthermore, the printer is equipped with USB and Ethernet connectivity options, providing flexibility in how it can be deployed within an organization.

In conclusion, the FARGO Electronic Quattro ID Card Printer is a powerful tool for creating secure, professional-grade identification cards. With its advanced printing technology, dual-sided printing capability, smart card encoding, and user-friendly features, it stands out as a reliable choice for organizations looking to enhance their ID card issuance processes. Whether for employee badges, student IDs, or membership cards, the Quattro printer is an excellent investment in security and quality.
Top Page Image Contents