FARGO electronic Quatro ID Card Printer manual II. Standard Printhead Cleaning

Page 32

IMPORTANT! 1. Unplug the printerÕs main power cord before performing any type of maintenance procedure unless otherwise indicated. Also, never use a sharp tool or a metal object of any kind to clean the printhead. You will damage the printhead!

2.Watches, rings, bracelets, and other jewelry can damage the printhead if accidentally bumped against it. For best results, remove such items before touching any internal components of printer.

3.Internal components of the printer, such as the printhead, may be damaged if exposed to static electrical discharges generated by various means, such as walking on a carpeted floor. To avoid potential damage, always wear an appropriate personal grounding device, such as a wrist strap (w/ integral resistor) connected to an ESD ground. Or, at a minimum, make positive contact with the bare metal chassis of the printer with your hand prior to touching any internal electrical components.

II.STANDARD PRINTHEAD CLEANING

This procedure should be performed if you notice a streak on the card where color was not transferred. This procedure should also be performed during every ribbon change or after every 250 prints in order to maintain consistent print quality.

1.Open the Top Cover of the printer by gently grasping the front sides of the cover and lifting upward. The cover will tilt open from front-to-back.

2.Open the Printhead Assembly by gently pulling up on the assemblyÕs Release Tab and lifting upward. Allow the assembly to swing completely open.

3.If you observe dust and/or other particles laying on the top surface of the ribbon, manually roll it up into the take- up roll. Occasionally, dust may settle on the top surface of the ribbon and cause print quality problems.

4.Use a Printhead Cleaning Pen from the Printer Cleaning Kit or a soft, lint-free cloth slightly moistened with isopropyl alcohol to wipe dust and other accumulated particles off the surface of the printhead. If using a cloth, be extremely careful not to use too much alcohol. It must not be allowed to drip into the printer!

28 Maintenance

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Quatro ID Card Printer UserÕs Manual Printing History Table of Contents Appendix a Magnetic Stripe Encoding Module Getting Started Thank YOUChoosing a Good Location II. about Moisture CondensationIII. Unpacking and Inspection Powering Up the Printer Applying PowerPower Input Port II. Identifying the Printer Features Ribbons and Cards About RibbonsII. Loading Ribbon Into the Printer Release Tab Printhead Assembly Take-up Ribbon Supply Ribbon Drive Hubs Ribbon Sensor III. about Cards IV. Loading Cards Into the PrinterCard Stack Card Input Tray Printing a Self Test Using the Quatro ID Card Printer Connecting the Printer to Your ComputerII. Installing the Windows Printer Driver Windows 95/98 or Windows NTWindows III. Installing the 32-BIT Print Spooler for Windows 95/98 PanelUsing the Quatro ID Card Printer IV. Setting UP the Windows Printer Driver Card Size Windows 95/98Windows NT Color Matching ControlsDither Mode Fast 32-bit SpoolerPanel Graphics No Margins Mag Encode OnlyMagnetics Position Rear of PrinterWrite Direct to Port Ribbon TypeRotate Printing a Card Maintenance Supplies RequiredII. Standard Printhead Cleaning III. Expanded Printhead Cleaning IV. Cleaning the PRINTER’S CaseCleaning the Inside of the Printer VI. Clearing a Card JAMVIII. Cleaning the Card Feed Rollers VII. Clearing a Ribbon JAMInsert this end first Sticky Side Up IX. Cleaning the Drive Roller Maintaining the Cleaning RollersMaintenance On-line LED light is flashing TroubleshootingPrinter doesn’t work at all On/cancel LED light is flashing ’m having problems printing from Windows 95/98Ribbon doesn’t seem to wind or print properly Card or ribbon is jammed Ribbon has torn or even brokenMy prints have streaks in them My prints have blotches small voids in themPhotos on my ID cards look very pixelated Card won’t feed and the on-line LED starts blinkingPrinting gets cut off or is not centered on the card Two or more cards feed at the same timeTechnical Specifications Printing AreaEncoding Mode / Magnetic Track Selection Magnectic Track OptionsMagnetic Track Options Encoded Bit DensityLRC Generation Mode Character Data SizeCharacter Ascii Offset Character Data ParityII. Track Locations III. Sending Track Information~1%JULIE ANDERSON623-85-1253? II. CENTRONICS-TYPE Parallel Interface Appendix B Interfacing InformationIntroduction Index Drive rollerRibbon type Page

Quatro ID Card Printer specifications

The FARGO Electronic Quattro ID Card Printer is a versatile and efficient solution for creating high-quality identification cards. This state-of-the-art printer is designed to cater to a variety of industries, including education, healthcare, and corporate environments, making it an ideal choice for organizations that require reliable and secure ID card printing.

One of the standout features of the Quattro ID Card Printer is its ability to produce vibrant, full-color cards with exceptional clarity. Utilizing advanced dye-sublimation technology, the printer ensures that images and text are reproduced with remarkable precision. The printer has a resolution of 300 dpi, providing sharp details and rich colors that enhance the overall appearance of the ID cards.

Another key characteristic of the Quattro printer is its dual-sided printing capability. This feature allows users to print on both sides of the card in a single pass, significantly reducing production time and enhancing productivity. Organizations can utilize the back side of the card for vital information, such as magnetic stripes, barcodes, or additional identification details.

The Quattro ID Card Printer also incorporates smart card encoding technology, which enables the printing and encoding of RFID and smart chip technology onto cards. This is particularly beneficial for organizations that require heightened security measures, as it allows for the storage of sensitive information directly on the ID card itself.

User-friendliness is another essential aspect of the FARGO Quattro ID Card Printer. The device features an intuitive interface with easy-to-navigate controls, making it accessible for operators of all skill levels. Additionally, the printer is designed for seamless integration with existing software systems, facilitating a smooth workflow.

The robust build and compact design of the Quattro printer make it suitable for a variety of settings. Its durable construction ensures longevity while occupying minimal space on a desk or workstation. Furthermore, the printer is equipped with USB and Ethernet connectivity options, providing flexibility in how it can be deployed within an organization.

In conclusion, the FARGO Electronic Quattro ID Card Printer is a powerful tool for creating secure, professional-grade identification cards. With its advanced printing technology, dual-sided printing capability, smart card encoding, and user-friendly features, it stands out as a reliable choice for organizations looking to enhance their ID card issuance processes. Whether for employee badges, student IDs, or membership cards, the Quattro printer is an excellent investment in security and quality.
Top Page Image Contents