Kyocera FS-3700 Firmware version information, Current status information, 3a Default font name

Page 42

2.2. Operating Procedures

1 — Firmware version information

The printer’s firmware version number and release date.

2 — Current status information

This information gives the printer’s temporary settings which are made by application or PRE- SCRIBE II commands or software. Note that this information pertains to the current interface only.

Emulation type is indicated by the one of the following numbers.

0-Line printer

1-IBM Proprinter X24E

2-Diablo 630

5-Epson LQ-850

6-HP LaserJet 4 Plus

3 — Interface-dependent parameters

By default, each one column for the serial and parallel interfaces appears on the status page and any changes in the settings affect the serial or parallel interface respectively. With an op- tional interface installed, a column for the option interface is also displayed.

These parameters may be set independently for each interface, i.e. changes made to the set- tings for one interface do not affect the other interface(s). Commands to change these set- tings affect the interface on which the command was received. Some of these settings may also be changed from the printer’s front panel by first selecting the desired interface and then changing the setting. For more information on setting these parameters, see the PRESCRIBE II Programming manual Chapter 5, Permanent Parameters.

3a — Default font name (V3)

The power-up scalable font (if specified) for each interface is listed here. The example which follows indicates that the power-up scalable font is AudreyTwo-RegularSWC on the parallel in- terface.

3a

4 — Non interface dependent parameters

These parameters affect all interfaces simultaneously. Any changes made with these parame- ters may interfere with the jobs on the other interface(s).

2-10

Image 42

Contents FS-1700/3700 Introduction Typeface Trademark Acknowledgement CC statement Conforming to the Class a limitsImportant note on the interface connectors Interface connectorsSafety information Laser safetyOzone concentration Laser noticeImportant Safeguards Disclaimer Canadian Department of Communications compliance statementISO Prolonged Non-Use and Moving the PrinterPower consumption FS-1700 Minutes 30 minutesFS-3700 Minutes 60 minutes Maintenance Features Print Engine FeaturesIntroduction Software Features Guide to the Manual Installation ManualOptions CD-ROM Kyocera Digital LibraryXii Table of Contents Xiv Fonts Xvi Memory Expansion Installation Printing condition Resolution 300 dpi 600 dpiRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Simm to be used Total printer Memory Type and number of SIMMsInstalling and Removing SIMMs Installing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi On-line/Off-line Setting Feed Selec ionAbandoning a Printing Job Operating Procedures Status PrintoutSample Status Current status information 3a Default font nameFirmware version information Interface-dependent parametersMemory allocation status Service informationForm Feed User defined font listUsing the Mode Select Menu Mode Select MenuFunct on Default Setting Function Default Setting ModePlease2.4. waitSleep Ecopower Mode KIR Level Dark vertical strip s Ecoprint modeOptimized stripes White vertical stripesAdjusting the Print Density SourceResource ProtectionSetting the Audio Warning Buzzer Priority Error Mess geSetting the Audio Warning Buzzer Operating a Memory Card Hints on Writing Fonts to the Memory CardReading Fonts/Data from a Memory Card Writing Da To a Memory Card MemoryDeleting Ddata from a Memory Card Formatting a Memory Card Formatting destroys any existing data on the memory cardPrinting a list of data names Fonts Bitmap and Scalable FontsBitmap fonts Scalable fontsList of Fonts Option FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol setScalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning Cleaning the Charger WireMain Charger Unit Cleaning the Grid Paper Feed Unit General Guide If the printer does not printIf the printing is abnormal Power Problems Interface ProblemsAll-black printout Print Quality ProblemsCompletely blank printout Check the developer unitBlack or white vertical streaks Clean the charger wireDropouts, horizontal streaks, stray dots Check the control panelFaint or blurred printing Grey backgroundCheck the paper chute and the ramp Dirt on the top edge or back of the paperCharacters out of position Check the transfer rollerIndicators and Messages IndicatorsIndicator Condition Correc ive Action Message Corrective Action KeyError Messages CallservicepersonFn123456Foccupied Correcting a Paper Jam Feed cassette Reaching the registration rollers, removeRear Cover MenuNormal CodesetError due to insufficient Description FS-1700 FS-3700Printer Specifications General Guidelines Paper AvailabilitySelecting the Right Paper Paper SpecificationsSpecification Condition of the PaperPaper Size Basis WeightMoisture Content SmoothnessPaper Grain Other Paper PropertiesSpecial Paper Overhead Projection OHP FilmTable B.4 lists the specifications for adhesive label paper Adhesive-Backed LabelsPreprinted Paper EnvelopesColored Paper Recycled PaperParallel Interface Parallel interface communication modesInterface Signals Pin In/out DescriptionDetailed descriptions of the signals follow Select In NSelectIn Pin RS-232C/RS-422A Interface Interface SignalsPin In/out Signal Description RS-232C interfaceRS-422A interface Removing*the Main Circuit BoardChanging the Jumper Connector Verifying the Setting Overview of Signals RS-422ASerial Connector RS-422A interface voltage levelsRS-232C/RS-422A Protocol Parameter value Baud rateMeaning Error not handled Error handled Prescribe II Frpo D0 commandSerial interface error Parameter value MeaningConnecting the Printer to the Computer RS-232C Cable ConnectionPreparing an RS-232C Cable Cmode LPT1=COM1 Index LastIndex-2 Index-3