Kyocera FS-3700 manual Parallel Interface, Parallel interface communication modes

Page 101

C.1. Parallel Interface

Appendix C

Host Computer Interface

This appendix describes the signals used in the laser printer’s parallel, RS-232C/RS-422A interfaces. It also lists pin assignments, signal functions, timings, connector specifica- tions, and voltage levels. The RS-232C/RS-422A protocols are also covered. Finally, it ex- plains the use of the printer in a multi-computer environment.

C.1. Parallel Interface

Parallel interface communication modes

The printer features the fast data transmission on the parallel interface. The parallel interface mode can be activated from the printer’s control panel (see Chapter 2, Operating the Page *Printer ) as follows:

Use a parallel printer cable that complies with the IEEE1284 standards.

Auto

The printer automatically changes its communication mode to the one the host computer is currently using.

Normal

The printer uses the communication method discribed by to the normal definitions of the Cen- tronics interface.

High-speed

This mode enables faster data transmission between the printer and the host computer.

C-1

Image 101

Contents FS-1700/3700 Introduction Typeface Trademark Acknowledgement Conforming to the Class a limits CC statementSafety information Interface connectorsImportant note on the interface connectors Laser safetyLaser notice Ozone concentrationImportant Safeguards ISO Canadian Department of Communications compliance statementDisclaimer Prolonged Non-Use and Moving the PrinterFS-3700 Minutes 60 minutes Power consumptionFS-1700 Minutes 30 minutes Introduction Maintenance FeaturesPrint Engine Features Software Features Options Installation ManualGuide to the Manual CD-ROM Kyocera Digital LibraryXii Table of Contents Xiv Fonts Xvi Removing the Main Circuit Board Memory Expansion InstallationPrinting condition Resolution 300 dpi 600 dpi Withdrawing the Main Circuit Board from the Printer Total printer Memory Type and number of SIMMs Simm to be usedRemoving SIMMs Installing and Removing SIMMsInstalling SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Abandoning a Printing Job On-line/Off-line SettingFeed Selec ion Status Printout Operating ProceduresSample Status Firmware version information 3a Default font nameCurrent status information Interface-dependent parametersForm Feed Service informationMemory allocation status User defined font listFunct on Default Setting Using the Mode Select MenuMode Select Menu Mode Function Default SettingPlease2.4. waitSleep Ecopower Mode KIR Level Optimized stripes Ecoprint modeDark vertical strip s White vertical stripesSourceResource Protection Adjusting the Print DensityPriority Error Mess ge Setting the Audio Warning BuzzerSetting the Audio Warning Buzzer Reading Fonts/Data from a Memory Card Operating a Memory CardHints on Writing Fonts to the Memory Card Memory Writing Da To a Memory CardDeleting Ddata from a Memory Card Formatting destroys any existing data on the memory card Formatting a Memory CardPrinting a list of data names Bitmap and Scalable Fonts FontsScalable fonts Bitmap fontsKpdl fonts List of FontsOption Fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol setScalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Main Charger Unit CleaningCleaning the Charger Wire Cleaning the Grid Paper Feed Unit If the printing is abnormal General GuideIf the printer does not print Interface Problems Power ProblemsCompletely blank printout Print Quality ProblemsAll-black printout Check the developer unitDropouts, horizontal streaks, stray dots Clean the charger wireBlack or white vertical streaks Check the control panelGrey background Faint or blurred printingCharacters out of position Dirt on the top edge or back of the paperCheck the paper chute and the ramp Check the transfer rollerIndicator Condition Correc ive Action Indicators and MessagesIndicators Key Message Corrective ActionCallservicepersonFn123456 Error MessagesFoccupied Feed cassette Reaching the registration rollers, remove Correcting a Paper JamRear Cover Codeset MenuNormalError due to insufficient FS-1700 FS-3700 DescriptionPrinter Specifications Paper Availability General GuidelinesSpecification Paper SpecificationsSelecting the Right Paper Condition of the PaperMoisture Content Basis WeightPaper Size SmoothnessOther Paper Properties Paper GrainOverhead Projection OHP Film Special PaperAdhesive-Backed Labels Table B.4 lists the specifications for adhesive label paperColored Paper EnvelopesPreprinted Paper Recycled PaperParallel interface communication modes Parallel InterfacePin In/out Description Interface SignalsDetailed descriptions of the signals follow Select In NSelectIn Pin Pin In/out Signal Description Interface SignalsRS-232C/RS-422A Interface RS-232C interfaceRemoving*the Main Circuit Board RS-422A interfaceChanging the Jumper Connector Overview of Signals RS-422A Verifying the SettingRS-422A interface voltage levels Serial ConnectorMeaning RS-232C/RS-422A ProtocolParameter value Baud rate Serial interface error Prescribe II Frpo D0 commandError not handled Error handled Parameter value MeaningPreparing an RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cmode LPT1=COM1 Last IndexIndex-2 Index-3