Kyocera FS-3700 manual Do not cap the new waste toner bot- tle

Page 74

4.1. Toner Kit Replacement

5.Locate the new waste toner bottle in the

toner kit, and install in the printer as shown right.

Do not cap the new waste toner bot- tle.

Insert the new waste toner bottle with the bottle tilted slightly towards you as shown in the figure.

New Waste Toner Bottle

6.After ensuring that the bottle is correctly

installed, close the side cover.

4-5

Image 74
Contents FS-1700/3700 Introduction Typeface Trademark Acknowledgement CC statement Conforming to the Class a limitsImportant note on the interface connectors Interface connectorsSafety information Laser safetyOzone concentration Laser noticeImportant Safeguards Disclaimer Canadian Department of Communications compliance statementISO Prolonged Non-Use and Moving the PrinterFS-3700 Minutes 60 minutes Power consumptionFS-1700 Minutes 30 minutes Introduction Maintenance FeaturesPrint Engine Features Software Features Guide to the Manual Installation ManualOptions CD-ROM Kyocera Digital LibraryXii Table of Contents Xiv Fonts Xvi Removing the Main Circuit Board Memory Expansion InstallationPrinting condition Resolution 300 dpi 600 dpi Withdrawing the Main Circuit Board from the Printer Simm to be used Total printer Memory Type and number of SIMMsRemoving SIMMs Installing and Removing SIMMsInstalling SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Abandoning a Printing Job On-line/Off-line SettingFeed Selec ion Operating Procedures Status PrintoutSample Status Current status information 3a Default font nameFirmware version information Interface-dependent parametersMemory allocation status Service informationForm Feed User defined font listFunct on Default Setting Using the Mode Select MenuMode Select Menu Function Default Setting ModePlease2.4. waitSleep Ecopower Mode KIR Level Dark vertical strip s Ecoprint modeOptimized stripes White vertical stripesAdjusting the Print Density SourceResource ProtectionSetting the Audio Warning Buzzer Priority Error Mess geSetting the Audio Warning Buzzer Reading Fonts/Data from a Memory Card Operating a Memory CardHints on Writing Fonts to the Memory Card Writing Da To a Memory Card MemoryDeleting Ddata from a Memory Card Formatting a Memory Card Formatting destroys any existing data on the memory cardPrinting a list of data names Fonts Bitmap and Scalable FontsBitmap fonts Scalable fontsKpdl fonts List of FontsOption Fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol setScalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Main Charger Unit CleaningCleaning the Charger Wire Cleaning the Grid Paper Feed Unit If the printing is abnormal General GuideIf the printer does not print Power Problems Interface ProblemsAll-black printout Print Quality ProblemsCompletely blank printout Check the developer unitBlack or white vertical streaks Clean the charger wireDropouts, horizontal streaks, stray dots Check the control panelFaint or blurred printing Grey backgroundCheck the paper chute and the ramp Dirt on the top edge or back of the paperCharacters out of position Check the transfer rollerIndicator Condition Correc ive Action Indicators and MessagesIndicators Message Corrective Action KeyError Messages CallservicepersonFn123456Foccupied Correcting a Paper Jam Feed cassette Reaching the registration rollers, removeRear Cover MenuNormal CodesetError due to insufficient Description FS-1700 FS-3700Printer Specifications General Guidelines Paper AvailabilitySelecting the Right Paper Paper SpecificationsSpecification Condition of the PaperPaper Size Basis WeightMoisture Content SmoothnessPaper Grain Other Paper PropertiesSpecial Paper Overhead Projection OHP FilmTable B.4 lists the specifications for adhesive label paper Adhesive-Backed LabelsPreprinted Paper EnvelopesColored Paper Recycled PaperParallel Interface Parallel interface communication modesInterface Signals Pin In/out DescriptionDetailed descriptions of the signals follow Select In NSelectIn Pin RS-232C/RS-422A Interface Interface SignalsPin In/out Signal Description RS-232C interfaceRS-422A interface Removing*the Main Circuit BoardChanging the Jumper Connector Verifying the Setting Overview of Signals RS-422ASerial Connector RS-422A interface voltage levelsMeaning RS-232C/RS-422A ProtocolParameter value Baud rate Error not handled Error handled Prescribe II Frpo D0 commandSerial interface error Parameter value MeaningPreparing an RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cmode LPT1=COM1 Index LastIndex-2 Index-3