Kyocera FS-3700 manual Error Messages, CallservicepersonFn123456

Page 86

5.5. Indicators and Messages

MessageE

Corrective Action

 

 

 

n012

 

 

Mechanical error ( = , , , ...)—Call a service person. The printer does

CallservicepersonFn:123456

not operate when a message beginning with Eis displayed. The total number

of pages printed is also indicated.

 

 

 

n012

 

 

Controller error ( = , , , ...)—Call a service person. The printer does

 

 

not operate when a message beginning with Fis displayed. The al number

 

 

of p es printed is also indicated.

 

 

 

 

 

Error Messages

 

 

Table 5.3 Err r Messages

 

 

 

 

 

 

MemoyoverMessageflow

Corrective Action

 

 

 

The total amount of data received by the printer exceeds the printer’s internal

 

 

memory. Try adding more memory (expansion RAM). Pre

the CONT key to

..PrintPressCONTrun

resume printing. You can abandon printing by the CANCEL key.

 

 

The data transferr d to the printer was too complex to print on a pa e. Press

 

 

the CONT key to resume printing. (The page may break in

ome pages.)

 

 

You can abandon prin ing by the CANCEL key.

 

 

 

Note: After this message has been displayed, Page prot ct mode w ll be

 

 

On>Pageprotect. To maintain optimum use of memory during pri ting, display

 

 

from the control panel, and re-sel ct Auto.

MEMORYInsertCARDagainerr

See the last page in this manual.

 

 

 

The memory card is accidentally removed from the printer’s memory c rd slot

 

 

during reading. If you continue reading the memory card, insert the s me

 

 

memory card into the slot again. The printer again reads it from the

 

 

beginning of the data.

 

 

 

Note: We recommend that you follow the reading procedure from the

Insertthesame

beginning to ensure correct reading of the memory card.

 

 

You have inserted the wrong memory card when the Insertagain

 

 

message was displayed. Remove the wrong memory card from the printer’s

 

 

memory card slot and insert the correct memory card. The printer again reads it

Fomaererror

from the beginning of the data.

 

 

 

This message appears when the printer is in the ready state and the memory

 

 

card is not formatted, and therefore cannot be read or written. Follow the

Watteryningbattery

procedure on Section 2.10. to format the card.

 

 

 

This message appears when the printer is in the ready state and the battery in

 

 

the memory card is low. You can still enter the memory card mode, but the

BMEMORYCARD

battery should be changed as soon as possible.

 

 

 

This message appears when the printer is in the ready state and the battery in

 

 

the memory card is dead, or there is no battery at all. It is not possible to use

 

 

the memory card mode until you insert a good battery in the card.

 

 

 

 

5-9

Image 86
Contents FS-1700/3700 Introduction Typeface Trademark Acknowledgement CC statement Conforming to the Class a limitsImportant note on the interface connectors Interface connectorsSafety information Laser safetyOzone concentration Laser noticeImportant Safeguards Disclaimer Canadian Department of Communications compliance statementISO Prolonged Non-Use and Moving the PrinterFS-3700 Minutes 60 minutes Power consumptionFS-1700 Minutes 30 minutes Introduction Maintenance FeaturesPrint Engine Features Software Features Guide to the Manual Installation ManualOptions CD-ROM Kyocera Digital LibraryXii Table of Contents Xiv Fonts Xvi Removing the Main Circuit Board Memory Expansion InstallationPrinting condition Resolution 300 dpi 600 dpi Withdrawing the Main Circuit Board from the Printer Simm to be used Total printer Memory Type and number of SIMMsRemoving SIMMs Installing and Removing SIMMsInstalling SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Abandoning a Printing Job On-line/Off-line SettingFeed Selec ion Operating Procedures Status PrintoutSample Status Current status information 3a Default font nameFirmware version information Interface-dependent parametersMemory allocation status Service informationForm Feed User defined font listFunct on Default Setting Using the Mode Select MenuMode Select Menu Function Default Setting ModePlease2.4. waitSleep Ecopower Mode KIR Level Dark vertical strip s Ecoprint modeOptimized stripes White vertical stripesAdjusting the Print Density SourceResource ProtectionSetting the Audio Warning Buzzer Priority Error Mess geSetting the Audio Warning Buzzer Reading Fonts/Data from a Memory Card Operating a Memory CardHints on Writing Fonts to the Memory Card Writing Da To a Memory Card MemoryDeleting Ddata from a Memory Card Formatting a Memory Card Formatting destroys any existing data on the memory cardPrinting a list of data names Fonts Bitmap and Scalable FontsBitmap fonts Scalable fontsKpdl fonts List of FontsOption Fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol setScalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Main Charger Unit CleaningCleaning the Charger Wire Cleaning the Grid Paper Feed Unit If the printing is abnormal General GuideIf the printer does not print Power Problems Interface ProblemsAll-black printout Print Quality ProblemsCompletely blank printout Check the developer unitBlack or white vertical streaks Clean the charger wireDropouts, horizontal streaks, stray dots Check the control panelFaint or blurred printing Grey backgroundCheck the paper chute and the ramp Dirt on the top edge or back of the paperCharacters out of position Check the transfer rollerIndicator Condition Correc ive Action Indicators and MessagesIndicators Message Corrective Action KeyError Messages CallservicepersonFn123456Foccupied Correcting a Paper Jam Feed cassette Reaching the registration rollers, removeRear Cover MenuNormal CodesetError due to insufficient Description FS-1700 FS-3700Printer Specifications General Guidelines Paper AvailabilitySelecting the Right Paper Paper SpecificationsSpecification Condition of the PaperPaper Size Basis WeightMoisture Content SmoothnessPaper Grain Other Paper PropertiesSpecial Paper Overhead Projection OHP FilmTable B.4 lists the specifications for adhesive label paper Adhesive-Backed LabelsPreprinted Paper EnvelopesColored Paper Recycled PaperParallel Interface Parallel interface communication modesInterface Signals Pin In/out DescriptionDetailed descriptions of the signals follow Select In NSelectIn Pin RS-232C/RS-422A Interface Interface SignalsPin In/out Signal Description RS-232C interfaceRS-422A interface Removing*the Main Circuit BoardChanging the Jumper Connector Verifying the Setting Overview of Signals RS-422ASerial Connector RS-422A interface voltage levelsMeaning RS-232C/RS-422A ProtocolParameter value Baud rate Error not handled Error handled Prescribe II Frpo D0 commandSerial interface error Parameter value MeaningPreparing an RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cmode LPT1=COM1 Index LastIndex-2 Index-3