Kyocera FS-3700 manual Cleaning the Grid

Page 76

4.2. Cleaning

Cleaning the Grid

1.Take the grid cleaner from protective bag in the new toner kit, and remove the cap.

☛The grid cleaner pad is impregnated with water. Perform the following cleaning procedure before the pad dries.

2.Attach the grid cleaner to the printer with the pad uppermost, as shown in the dia- gram.

Protective Bag	Cap

Grid Cleaner

Grid Cleaner

3.After attaching the grid cleaner, repeat the action of slowly pulling out and then pushing back in the main charger unit at least 5 times. It is easier to pull out the main charger for the first time if it is raised slightly, as shown in the figure.

The grid part underneath the main charger is cleaned by this procedure.

(1)

(3)

(2)

Main Charger Unit

4.When the grid is clean, remove the grid cleaner from the printer and dispose of it. The grid cleaner is not re-usable.

5.After cleaning the charger wire, push the cleaning knob all the way in and close the side cover.

4-7

Image 76

Contents FS-1700/3700 Introduction Typeface Trademark Acknowledgement CC statement Conforming to the Class a limitsInterface connectors Safety informationImportant note on the interface connectors Laser safetyOzone concentration Laser noticeImportant Safeguards Canadian Department of Communications compliance statement ISODisclaimer Prolonged Non-Use and Moving the PrinterFS-1700 Minutes 30 minutes Power consumptionFS-3700 Minutes 60 minutes Print Engine Features Maintenance FeaturesIntroduction Software Features Installation Manual OptionsGuide to the Manual CD-ROM Kyocera Digital LibraryXii Table of Contents Xiv Fonts Xvi Printing condition Resolution 300 dpi 600 dpi Memory Expansion InstallationRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Simm to be used Total printer Memory Type and number of SIMMsInstalling SIMMs Installing and Removing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Feed Selec ion On-line/Off-line SettingAbandoning a Printing Job Operating Procedures Status PrintoutSample Status 3a Default font name Firmware version informationCurrent status information Interface-dependent parametersService information Form FeedMemory allocation status User defined font listMode Select Menu Using the Mode Select MenuFunct on Default Setting Function Default Setting ModePlease2.4. waitSleep Ecopower Mode KIR Level Ecoprint mode Optimized stripesDark vertical strip s White vertical stripesAdjusting the Print Density SourceResource ProtectionSetting the Audio Warning Buzzer Priority Error Mess geSetting the Audio Warning Buzzer Hints on Writing Fonts to the Memory Card Operating a Memory CardReading Fonts/Data from a Memory Card Writing Da To a Memory Card MemoryDeleting Ddata from a Memory Card Formatting a Memory Card Formatting destroys any existing data on the memory cardPrinting a list of data names Fonts Bitmap and Scalable FontsBitmap fonts Scalable fontsOption Fonts List of FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol setScalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning the Charger Wire CleaningMain Charger Unit Cleaning the Grid Paper Feed Unit If the printer does not print General GuideIf the printing is abnormal Power Problems Interface ProblemsPrint Quality Problems Completely blank printoutAll-black printout Check the developer unitClean the charger wire Dropouts, horizontal streaks, stray dotsBlack or white vertical streaks Check the control panelFaint or blurred printing Grey backgroundDirt on the top edge or back of the paper Characters out of positionCheck the paper chute and the ramp Check the transfer rollerIndicators Indicators and MessagesIndicator Condition Correc ive Action Message Corrective Action KeyError Messages CallservicepersonFn123456Foccupied Correcting a Paper Jam Feed cassette Reaching the registration rollers, removeRear Cover MenuNormal CodesetError due to insufficient Description FS-1700 FS-3700Printer Specifications General Guidelines Paper AvailabilityPaper Specifications SpecificationSelecting the Right Paper Condition of the PaperBasis Weight Moisture ContentPaper Size SmoothnessPaper Grain Other Paper PropertiesSpecial Paper Overhead Projection OHP FilmTable B.4 lists the specifications for adhesive label paper Adhesive-Backed LabelsEnvelopes Colored PaperPreprinted Paper Recycled PaperParallel Interface Parallel interface communication modesInterface Signals Pin In/out DescriptionDetailed descriptions of the signals follow Select In NSelectIn Pin Interface Signals Pin In/out Signal DescriptionRS-232C/RS-422A Interface RS-232C interfaceRS-422A interface Removing*the Main Circuit BoardChanging the Jumper Connector Verifying the Setting Overview of Signals RS-422ASerial Connector RS-422A interface voltage levelsParameter value Baud rate RS-232C/RS-422A ProtocolMeaning Prescribe II Frpo D0 command Serial interface errorError not handled Error handled Parameter value MeaningRS-232C Cable Connection Connecting the Printer to the ComputerPreparing an RS-232C Cable Cmode LPT1=COM1 Index LastIndex-2 Index-3