Kyocera FS-3700 manual Feed Selec ion, On-line/Off-line Setting, Abandoning a Printing Job

Page 39

Cassette

2.2. Operating Procedures

 

Feed Selec ion

The FEED key lec s he paper feed cassette [Cassette] or multi -purpose tray [MPtray] (or the option paper feeder[s], if installed) as the paper ource. The FEED key can be used whenever the message display indicat s Readyor Addpaper.

Press the FEED key. The selection cycles and is moment rily displayed in the messMPgetraydisplay as:

The current selection is indicated by a green light on the printer symbol above the key.

On-line/Off-line Setting

By pressing the ON LINE key you can change the print r between the on-line state, in which it prints the data it receives from the computer, and the off-line state, in which it stores the data for printing later.

1.Make sure that the message display indicates Ready.

2.Press the ON LINE key.

If the printer is on-line, it changes to off-line. If the printer is off-line, it changes back to on

-line.

WaitingThe ON LINE indicator lights when the printer is on-line. Processing

Going off-line may or may not halt communication between the p inter and computer, de- pending on details of the current interface. While off-line, the printer ontinues to accept any data hat arrives until the current interface buffer is full, at which point it tructs the com-

puter o stop sending data. Data stored while off-line are printed when the pri ter is returned to the on-line state.

Abandoning a Printing Job

You can abandon a printing job before it is completed. If the printer is simulta eously receiv- da on more than one interface, you can selectively cancel the printing job on a particular

interface.

This procedure can be used while the message display indicatesor

.

2-7

Image 39
Contents FS-1700/3700 Introduction Typeface Trademark Acknowledgement Conforming to the Class a limits CC statementLaser safety Interface connectorsSafety information Important note on the interface connectorsLaser notice Ozone concentrationImportant Safeguards Prolonged Non-Use and Moving the Printer Canadian Department of Communications compliance statementISO DisclaimerPower consumption FS-1700 Minutes 30 minutesFS-3700 Minutes 60 minutes Maintenance Features Print Engine FeaturesIntroduction Software Features CD-ROM Kyocera Digital Library Installation ManualOptions Guide to the ManualXii Table of Contents Xiv Fonts Xvi Memory Expansion Installation Printing condition Resolution 300 dpi 600 dpiRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Total printer Memory Type and number of SIMMs Simm to be usedInstalling and Removing SIMMs Installing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi On-line/Off-line Setting Feed Selec ionAbandoning a Printing Job Status Printout Operating ProceduresSample Status Interface-dependent parameters 3a Default font nameFirmware version information Current status informationUser defined font list Service informationForm Feed Memory allocation statusUsing the Mode Select Menu Mode Select MenuFunct on Default Setting Mode Function Default SettingPlease2.4. waitSleep Ecopower Mode KIR Level White vertical stripes Ecoprint modeOptimized stripes Dark vertical strip sSourceResource Protection Adjusting the Print DensityPriority Error Mess ge Setting the Audio Warning BuzzerSetting the Audio Warning Buzzer Operating a Memory Card Hints on Writing Fonts to the Memory CardReading Fonts/Data from a Memory Card Memory Writing Da To a Memory CardDeleting Ddata from a Memory Card Formatting destroys any existing data on the memory card Formatting a Memory CardPrinting a list of data names Bitmap and Scalable Fonts FontsScalable fonts Bitmap fontsList of Fonts Option FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol setScalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning Cleaning the Charger WireMain Charger Unit Cleaning the Grid Paper Feed Unit General Guide If the printer does not printIf the printing is abnormal Interface Problems Power ProblemsCheck the developer unit Print Quality ProblemsCompletely blank printout All-black printoutCheck the control panel Clean the charger wireDropouts, horizontal streaks, stray dots Black or white vertical streaksGrey background Faint or blurred printingCheck the transfer roller Dirt on the top edge or back of the paperCharacters out of position Check the paper chute and the rampIndicators and Messages IndicatorsIndicator Condition Correc ive Action Key Message Corrective ActionCallservicepersonFn123456 Error MessagesFoccupied Feed cassette Reaching the registration rollers, remove Correcting a Paper JamRear Cover Codeset MenuNormalError due to insufficient FS-1700 FS-3700 DescriptionPrinter Specifications Paper Availability General GuidelinesCondition of the Paper Paper SpecificationsSpecification Selecting the Right PaperSmoothness Basis WeightMoisture Content Paper SizeOther Paper Properties Paper GrainOverhead Projection OHP Film Special PaperAdhesive-Backed Labels Table B.4 lists the specifications for adhesive label paperRecycled Paper EnvelopesColored Paper Preprinted PaperParallel interface communication modes Parallel InterfacePin In/out Description Interface SignalsDetailed descriptions of the signals follow Select In NSelectIn Pin RS-232C interface Interface SignalsPin In/out Signal Description RS-232C/RS-422A InterfaceRemoving*the Main Circuit Board RS-422A interfaceChanging the Jumper Connector Overview of Signals RS-422A Verifying the SettingRS-422A interface voltage levels Serial ConnectorRS-232C/RS-422A Protocol Parameter value Baud rateMeaning Parameter value Meaning Prescribe II Frpo D0 commandSerial interface error Error not handled Error handledConnecting the Printer to the Computer RS-232C Cable ConnectionPreparing an RS-232C Cable Cmode LPT1=COM1 Last IndexIndex-2 Index-3