Kyocera FS-3700 manual Close the top cover by pressing the ar

Page 72

4.1. Toner Kit Replacement

5.The bottom of the toner container is sealed with a plastic strip. Carefully pull the sealing strip off the toner container, making sure not to leak any toner. Dis- pose of the sealing strip.

6.Install the toner container on the devel- oper as shown in the diagram.

☛Be sure to peel off the seal on the toner container before mounting the toner container on the developer unit.

7.When the toner container is installed cor- rectly on the developer.

8.Push the top of the toner container unit ("PUSHHERE") until it locks in.

☛Make sure that the toner container is properly locked in the printer.

Sealing Strip

9. Close the top cover by pressing the ar-
..			printerCONTis displayed, the message Cleanprinter
row d part this diagram.
☛ It is neces a y to clean the inside of
the		i	ter after	placing the toner
cont		i	er.
IfCleanthe toner co				ainer is replaced when the message ReplaceToner
	press			will be displayed after replacement. After cleaning the in-

side of the printer (See Section 4.2. Cleaning), the message will disappear when the CONTkey is pressed, and the printer will be ready for printing.

4-3

Image 72

Contents FS-1700/3700 Introduction Typeface Trademark Acknowledgement CC statement Conforming to the Class a limitsInterface connectors Safety informationImportant note on the interface connectors Laser safetyOzone concentration Laser noticeImportant Safeguards Canadian Department of Communications compliance statement ISODisclaimer Prolonged Non-Use and Moving the PrinterPower consumption FS-1700 Minutes 30 minutesFS-3700 Minutes 60 minutes Maintenance Features Print Engine FeaturesIntroduction Software Features Installation Manual OptionsGuide to the Manual CD-ROM Kyocera Digital LibraryXii Table of Contents Xiv Fonts Xvi Memory Expansion Installation Printing condition Resolution 300 dpi 600 dpiRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Simm to be used Total printer Memory Type and number of SIMMsInstalling and Removing SIMMs Installing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi On-line/Off-line Setting Feed Selec ionAbandoning a Printing Job Operating Procedures Status PrintoutSample Status 3a Default font name Firmware version informationCurrent status information Interface-dependent parametersService information Form FeedMemory allocation status User defined font listUsing the Mode Select Menu Mode Select MenuFunct on Default Setting Function Default Setting ModePlease2.4. waitSleep Ecopower Mode KIR Level Ecoprint mode Optimized stripesDark vertical strip s White vertical stripesAdjusting the Print Density SourceResource ProtectionSetting the Audio Warning Buzzer Priority Error Mess geSetting the Audio Warning Buzzer Operating a Memory Card Hints on Writing Fonts to the Memory CardReading Fonts/Data from a Memory Card Writing Da To a Memory Card MemoryDeleting Ddata from a Memory Card Formatting a Memory Card Formatting destroys any existing data on the memory cardPrinting a list of data names Fonts Bitmap and Scalable FontsBitmap fonts Scalable fontsList of Fonts Option FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol setScalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning Cleaning the Charger WireMain Charger Unit Cleaning the Grid Paper Feed Unit General Guide If the printer does not printIf the printing is abnormal Power Problems Interface ProblemsPrint Quality Problems Completely blank printoutAll-black printout Check the developer unitClean the charger wire Dropouts, horizontal streaks, stray dotsBlack or white vertical streaks Check the control panelFaint or blurred printing Grey backgroundDirt on the top edge or back of the paper Characters out of positionCheck the paper chute and the ramp Check the transfer rollerIndicators and Messages IndicatorsIndicator Condition Correc ive Action Message Corrective Action KeyError Messages CallservicepersonFn123456Foccupied Correcting a Paper Jam Feed cassette Reaching the registration rollers, removeRear Cover MenuNormal CodesetError due to insufficient Description FS-1700 FS-3700Printer Specifications General Guidelines Paper AvailabilityPaper Specifications SpecificationSelecting the Right Paper Condition of the PaperBasis Weight Moisture ContentPaper Size SmoothnessPaper Grain Other Paper PropertiesSpecial Paper Overhead Projection OHP FilmTable B.4 lists the specifications for adhesive label paper Adhesive-Backed LabelsEnvelopes Colored PaperPreprinted Paper Recycled PaperParallel Interface Parallel interface communication modesInterface Signals Pin In/out DescriptionDetailed descriptions of the signals follow Select In NSelectIn Pin Interface Signals Pin In/out Signal DescriptionRS-232C/RS-422A Interface RS-232C interfaceRS-422A interface Removing*the Main Circuit BoardChanging the Jumper Connector Verifying the Setting Overview of Signals RS-422ASerial Connector RS-422A interface voltage levelsRS-232C/RS-422A Protocol Parameter value Baud rateMeaning Prescribe II Frpo D0 command Serial interface errorError not handled Error handled Parameter value MeaningConnecting the Printer to the Computer RS-232C Cable ConnectionPreparing an RS-232C Cable Cmode LPT1=COM1 Index LastIndex-2 Index-3