Emerson Understanding the ASCO Configurator and SNMP with the 4000 Series

Page 32

A-6 SNMP Internet-standard Protocol

Connectivity Module

Recommended ASCO SNMP MIB file

A file containing 934904-xxx.mib can be downloaded from the location shown below.

http://www.emersonnetworkpower.com/ en-US/Products/PowerSwitchingandControls/MonitoringandControl/Pages/ ASCO5150ConnectivityModuleAcc72E.aspx

The 934904-xxx.mib file is written in the MIB module definition language based on the SMI specifications. This protocol file contains a structure block of information pertaining to ATS status and analog data. When SNMP is enabled, the CM polls for the information and shares it with requesting SNMP manager(s). The SNMP manager must use the file as a reference in sending SNMP requests for ATS information.

Troubleshooting SNMP Configuration

Problem		Cause	Solution
SNMP Manager cannot communicate	-	Host running SNMP Manager is	- Check SNMP configuration at
with the Connectivity Module; do not		not in the same network or	Connectivity Module
get trap message after alarms occur.		Connectivity Module	configuration page.
	- SNMP is not enabled.		- Hook up a laptop to the same
			network and ping the
	- Incorrect SNMP IP Manager IP		Connectivity Module and SNMP
		addresses	Manager(s).
	-	Incorrect SNMP community
		setting.

Image 32

Contents Connectivity Module 381333-367 CWho Should Use this Installation Manual Ii Welcome Connectivity ModulePrerequisites Important informationSpecifications Installation OverviewCheck the DIP Switch Settings for RS485 DIP Switch on bottom of unitIv Outline and Mounting Drawing Connectivity Module Wiring Diagrams Connectivity Module Connectivity Module Wiring Diagrams Vii Wiring Diagrams Connectivity Module Connectivity Module Wiring Diagrams Connectivity Module Status LEDs LED Description LED Function / Mode of OperationStatus LEDs Installation How to Install the Connectivity Module on Asco 940/962 ATSsConnectivity Module Installation How to Test Communication to the Connectivity ModuleHttp//169.254.1.1/config.htm Installation Connectivity ModuleDevice Configurator Screen for 7000 & 4000 Series ATSs Group 5 Controller Configuration right sideConnectivity Module server Configuration left side Device Configurator Screen for 7000 & 4000 Series ATSs7000 & 4000 Series ATSs Connectivity Module Power Manager or Power Meter ConfigurationInput Name & Output Names Power Manager only Accessory 85 Descriptive Tags Assigned Detail Screen for 7000 & 4000 Series ATSs Device Configurator Screen for Series 300 ATSs Group 1 Controller Configuration right sideDevice Configurator Screen for Series 300 ATSs Connectivity Module Series 300 ATSsPower Meter Series 300 ATSs Connectity ModuleDetail Screen for Series 300 ATSs with a Power Manager Detail Screen for Series 300 ATSsPage Device Configurator Screen for Asco 940/962 ATSs Group 7A Controller Configuration right sideDevice Configurator Screen without Power Manager Device Configurator Screen with Power ManagerAsco 940/962 ATSs Connectivity Module Detail Screen for Asco 940/962 ATSs with a Power ManagerDetail Screen for Asco 940/962 ATSs Input names Display Input & Output Names screen Output names Detail Screen for Power Managers connected to a Load Detail Screen for Digital Power Meters connected to a LoadDetail Screen for Power Managers connected to a Generator Detail Screen for PowerDetail On Local Area Connection Properties screen Select All Programs Accessories Command Prompt Connectivity Module Troubleshooting A-3 Problem CauseThird Party Modbus Device Configuration Read RequestsConnectivity Module Snmp Internet-standard Protocol A-5 Snmp Trap messagesProblem Cause Solution Snmp Internet-standard Protocol Connectivity ModuleCatalog No Address set ATS Controller PM or DPM Row IP Address Subnet Mask GatewaySerial No Communication Address Form for Connectivity Module CM Communication Address Form for Connectivity Module CM Index